JCM TBV Series Training Download | Manualshive

Page: 26 / 40

background image

Part No. 960-100941R_Rev. A

© 2016 JCM American Corporation

2 6

October, 2016

JCM® Training Overview

TBV Transaction Based Validator

TBV ERROR CODE TABLES

This section identifies the Standard LED Error Codes for the TBV Unit. The
TBV Bezel LED will flash either

YELLOW,

GREEN

or

RED

when various

Error Conditions occur. Refer to Table 13 below for a list of TBV Banknote
Jam Error Codes and their solutions. The

LED Color Flash Sequence

column

indicates the number of times the Bezel LED flashes a particular color and the
corresponding Error. As an example, a single Yellow Flash indicates a
Banknote Jam Error at the Cash Box.

B

ANKNOTE

J

AM

E

RROR

C

ODES

Banknote Jams are indicated by the Bezel LED flashing a

YELLOW

color.

Count the number of Flashes between pauses to identify the Error, Causes and
Solutions.

Table 13

TBV Banknote Jam Error Codes

LED Color

Flash

Sequence

Error

Causes and Solutions

1

Banknote Jam

(Cash Box)

A Banknote jam is detected at the Cash Box.

[Solution] Check the Cash Box for a jammed Banknote.

[Relative Parts] Feed Motor, Stacker Sensor, Feed-Out Sensor

If the condition is not resolved, change the above related part or parts and
complete a Positioning Sensor Calibration procedure.

2

Banknote Jam

(Transport)

Sensors did not detect a Banknote present.

[Solution] Check for a jammed Banknote or foreign material. Check/clean all
Sensors.

[Relative Parts] Feed Motor, BNF Entrance Sensor, BNF Assignation
Sensor, Transport Entrance Sensor, Centering Sensor, Side Sensor,
Validation Sensor, Feed-Out Sensor

If the condition is not resolved, change the above related part or parts and
complete a full Calibration procedure.

3

Banknote

Chain

Sensors are blocked longer than specified.

[Solution] Check for a jammed Banknote or foreign material. Check/clean all
Sensors.

[Relative Parts] BNF Feed Roller, BNF Retard Roller, BNF Assignation
Sensor, Transport Entrance Sensor, Feed-Out Sensor

If the condition is not resolved, change the above related part or parts and
complete a full Calibration procedure.

4

Cash Box

Removed

Cash Box has been removed.

[Solution] Check that the Cash Box is seated properly.

[Relative Parts] Cash Box Sensor

If the condition is not resolved, change the above related part or parts.

5

Banknote

Transport Error

Sensors detected a Banknote with abnormal timing.

[Solution] Check for a jammed Banknote or foreign material. Check/clean all
Sensors.

[Relative Parts] Side Sensor, Validation Sensor, Feed-Out Sensor, Cash
Box Feed Out Sensor

If the condition is not resolved, change the above related part or parts and
complete a full Sensor Calibration procedure.

«
...
24
25
26
27
28
...
»

Summary of Contents for TBV Series









































Reviews:

No comments

Related manuals for TBV Series

Brand: CUMMINS ALLISON Pages: 28

Brand: Olympia Pages: 108

Brand: CPI Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands