background image

2. Wait a few seconds while the scan tool validates the PID MAP. 
 
3. If retrieved information covers more than one screen, use the 
  Direction button, as necessary, until all the data have been shown 

  up. 

•  If there is no freeze frame data available, an advisory message “No   
  freeze frame data stored!” shows on the display. 
 
4.    Press OK button to return to previous screen 
 

•  Retrieving I/M Readiness Status 

I/M Readiness function is used to check the operations of the 
Emission System on OBD2 compliant vehicles. It is an excellent 
function to use prior to having a vehicle inspected for compliance to 
a state emissions program. 
 
CAUTION - By clearing trouble codes you also clear the readiness 
status for the individual emission system readiness tests. In order to 
reset these monitors, the vehicle must be driven through a complete 
drive cycle with no trouble codes in memory. Times for reset vary 
depending on vehicle. 
 
Some latest vehicle models may support two types of I/M Readiness 
tests: 
1. Since DTCs Cleared - indicates status of the monitors since the   

DTCs are erased. 

2. This Drive Cycle - indicates status of monitors since the beginning 

of the current drive cycle. 

Summary of Contents for FasDiag JD301

























Reviews: