background image

An I/M Readiness Status result of “NO” does not necessarily indicate 
that the vehicle being tested will fail the state I/M inspection. For 
some states, one or more such monitors may be allowed to be “Not 
Ready” to pass the emissions inspection. 
1. 

“OK”

 - Indicates that a particular monitor being checked has   

  completed its diagnostic testing. 
2. 

“INC”

 - Indicates that a particular monitor being checked has not   

  completed its diagnostic testing. 
3. 

“N/A”

 - The monitor is not supported on that vehicle. 

 
There are two ways to retrieve I/M readiness status. 
1. Retrieve I/M Readiness status with One-Click I/M Readiness Key 
2. Retrieve I/M Readiness status in typical way 
 

•  Viewing Vehicle Information 

The Vehicle Info. function enables retrieval of Vehicle Identification   
No. (VIN), Calibration ID Nos. (CINs), Calibration Verification Nos. 
(CVNs) and In-use Performance Tracking on 2000 and newer 
vehicles that support Mode 9. 
 
1. Use Direction button to select Vehicle Info. from the Diagnostic   
  Menu and press OK button.   
 
2. An advisory message comes up to remind you. Wait a few seconds   
  or press any key to continue. 
 
3. Wait a few seconds while the scan tool reads vehicle information 

Summary of Contents for FasDiag JD301

























Reviews: