background image

 

 

GSM/GPRS/EDGE SIGNAL ANALYZER 

32 

 

JD7105B Base Station Analyzer 

 

 

DELTA:

 This Delta marker type is associated with a Normal marker. A Normal marker must be set 

before a Delta marker is set. When the Delta marker is set, the position set by the Delta marker 

becomes the reference position of the Normal marker and the marker’s X and Y values displays 

the difference compared with the Delta marker. 

 

DELTA PAIR:

 This Delta Pair marker type is associated with a Normal marker. A Normal marker 

must be set before a Delta Pair marker is set. When the Delta Pair marker is set, the position set 

by the Delta Pair marker becomes the reference position of the Normal marker and the marker’s X 

and Y values displays the difference compared with the Delta Pair marker. The reference position 

will be varied in accordance with trace change. 

 

MARKER ALL OFF:

 Turns all the markers the screen off. When the Marker View is selected for 

those markers, the instrument displays those markers back at the previous position. If a 

measurement mode is changed, current settings are not restored. 

 

Using Peak Search 

PEAK SEARCH 

 

Each time the Peak Search soft key is pressed, the active marker is positioned at the highest peak of 

the trace. 

 

 

PEAK SEARCH:

 Moves the active marker to the highest peak of the trace. 

 

NEXT PEAK:

 Moves the active marker to the second highest peak of the trace. 

 

NEXT PEAK RIGHT:

 Moves the active marker to the highest peak to the right of its current 

position. 

 

NEXT PEAK LEFT:

 Moves the active marker to the highest peak to the left of its current position. 

 

MIN SEARCH:

 Moves the active marker to the lowest peak of the trace. 

 

ALWAYS PEAK: 

When the 

Always Peak

 is set to On, the instrument moves the active marker 

automatically to the highest peak of the trace every time the trace is refreshed. 

 

 

Summary of Contents for JD7105B












































































Reviews: