6
3
Rotate the BIT clockwise 180º to seat the BIT into the WIRE WRAP GUN.
(Fig. 2)
When the BIT is seated properly, sqeezing the TRIGGER of the gun will make
the BIT spin.
6.
Locate the KEY SLOT on the SLEEVE. (Fig. 3)
With the KEY SLOT pointing DOWN, slide the SLEEVE over the BIT and
engage with the pin inside the COLLET NUT. (Fig. 4)
Tighten the COLLET NUT while squeezing the TRIGGER. This will create a
small amount of clearance between the BIT, SLEEVE, and BIT DRIVER to
prevent “locking” occurs, the BIT will slow or jam the gun and produce grind
-
ing sounds. (Fig. 5)
Gire la punta hacia la derecha 180º para asentar la punta en su lugar en la
pistola de Enrollado. (Figura 2)
Cuando la punta es asentada apropiadamente, apretando el gatillo de la pis-
tola hará girar la punta.
6. Localice la ranura en la manga. ( Figura 3)
Con la ranura hacia abajo, deslice la manga sobre la punta y posicione el
pivote dentro de su posición. (Figura 4)
Apriete la tuerca mientras actúa el gatillo, para crear una separación entre la
punta y la manga, así como la guía de la pistola. Esto previene que se apri-
sione el mecanismo o que se produzcan ruidos con fricción.
(Figura 5)
5.
5.
7.
7.
Wire Size Chart
A wire wrapped connection is made by coiling the wire around the sharp corners of a terminal under mechanical tension.
This method of connection was developed by Bell Telephone Laboratories, Western Electric Company.
Five Steps To Make A
Wire Wrap Connection
1
A “Regular” bit wraps the bare wire around the terminal. A “Modified” bit
wraps a portion of insulation around the terminal in addition to the bare wire.
This greatly increases the ability to withstand vibration.
A distinct advantage of wire wrapping is the ease with which a wire may
be removed from a terminal to correct errors or modify wiring. An unwrap
tool is slipped over the terminal, engaging the first turn of the connection.
Rotating the tool, the connection is removed in seconds, without damage to
the terminal.
2
3
4
5
Bare Wire Dia.
AWG
(USA)
SWG
(GB)
In.
mm
.0403
1.022
18
.040
1.016
19
.036
0.914
19
20
.032
0.813
20
21
.028
0.711
21
22
.0253
0.643
22
.024
0.61
23
.0226
0.574
23
.022
0.559
24
.0201
0.51
24
.020
0.508
25
.018
0.457
26
.0179
0.455
25
.0164
0.417
27
.0159
0.404
26
.0148
0.376
28
.0142
0.361
27
.0136
0.345
29
.0126
0.320
28
.0124
0.315
30
.0116
0.295
31
.0113
0.287
29
.0108
0.274
32
.0100
0.254
30
33
.0092
0.234
34
.0089
0.225
31
.0084
0.213
35
0.008
0.203
32
Regular
Modified
Terminal Diagonal Chart
Un enrollado de punta“Regular” la parte de cable sin aislamiento se enrolla
en la terminal. Un enrollado de punta ”Modificado” tiene una porción de
aislamiento del cable enrollado en la terminal. Esto aumenta la habilidad de
soportar vibración.
Una ventaja distintiva del enrollado de cables es lo fácil que el cable puede
ser removido del terminal para corregir errores o modificar cableados. Una
herramienta de desenrollado es deslizada sobre la terminal agarrando la
primera envoltura o conexión. Rotando la herramienta, la conexión es
removida en segundos, sin ocasionar daños a la terminal.
Regular
Modificado
Tabla de Calibres de Cable
Cinco Pasos para Hacer
una Conexión
Tabla para Identificar la Medida Diagonal de las Terminales
RANURA
KEY SLOT