background image

08

Chargers

- Longest life and best performance can be obtained if the battery 

pack is charged when the air temperature is between 18-24C. 

Do not charge the battery pack in a very low or very high air 

temperature.

- The Charger’s plug must match the outlet. Never modify the plug 

in any way.  Unmodified plugs and matching outlets will reduce risk 

of electric shock.

- Use your charger only to charge batteries of the type supplied 

with your tool.  Other batteries could burst, causing personal injury 

and damage.

- Only 2 battery packs are allowed to be charged continuously in 

order to prevent overheating of charger, necessary rest time is 

required to let the charger cool down before further charging.

- When charging is finished, unplug the charger from mains socket 

outlet and take away the battery pack from the charger, do not 

leave the battery pack in the charger.

- Never carry the charger by its cord or pull the cord to disconnect 

from the socket.  Keep the cord away from heat, oil and sharp 

edges.

- Never attempt to charge non-rechargeable batteries.

- The cord of charger is not changeable, do not continue to use if 

the cord is damaged.

- Do not expose to water or rain, do not use in wet conditions.

- Do not open the charger.

- Do not probe the charger.

- The charger is intended for indoor use only.

- The charger and battery pack may become warm to touch while 

charging. This is a normal condition, and does not indicate a 

problem.

Summary of Contents for ZQ561


















Reviews: