background image

Remote Controller Operation Manual

Made&Design in Taiwan

Peak Value Show / Clear Setting Function

Warning Setting When the OP value is Below, the warning will be functional

(

)

1. Please must follow all installations in this manual to ensure safe installation and operation of the product.
2. DO NOT disassemble or reassemble the product. This might cause damage or make them unsafe to use.

When the product is disassembled or reassembled, the Warranty can't be offered.

3. Before installation, please make sure the engine is switched off and the vehicle is stationary.
4. Due to possible injury from contact with a hot engine or exhaust pipe, DO NOT begin installation until the vehicle is cool.
5. When attaching wires for the product, please take care so that the product's wires do not interfere with existing wires.
6. This product is only for use on vehicles with 12V electronic system.

WARNING

1.

2.

Select icon by press

to enter Oil Pressure Setting Mode.

Then Press

to change the backlight. Press

to save the setting or idle

any button for 5 seconds to leave the setting mode.

CAUTION

Daemon

III

Fuel

-

Pressure Operation Manual

Gauge Contents :

Gauge*1 / Pressure Sensor*1 / Sensor Wire(3pin)*1 / Gauge Wire (6pin)*1 / Gauge Stand*1 / Operation Manual*1 /

(

)

Meter Visor*1 Optional

Gauge

RED: Ignition-Coil

Installation Diagram

Gauge Wire

Sensor Wire

BLACK: Ground

YELLOW: Dimmer 12V

Light (12V)

Pressure Sensor

Accessory

A/C

Ignition-Coil

Motor Starter

Battery

Ignition Switch Diagram

To avoid damage, please ensure the RED wire is attached to the ignition switch that connected to Coil.

1. To avoid oil leaks during installation of sensor, please use Telfon tape while installation. Before driving, inspect tubing

and oil blocks for leaks. Leaks could cause a fire or damage the engine.

2. To avoid oil leaks, please ensure the size of adaptor is suited.
3. To avoid the damage of sensor wire, please fix the waterproof connector on the vehicle body.
4. Oil spills by the installation work. Please replenish the engine with oil. The engine might overheat when oil is too little.

1. Please have the remote controller point to the gauge you are going to set up.
2. In setting process, press

directly; the gauge will leave setting mode and save.

3. A “beep” sound will be heard while the new setting is done.

1.

2.

3.

4.

5.

Water Temp

Oil

Pressure

Exhaust Temp

BOOST

Temp

Oil

11.

12.

13.

14.

15.

Warning

Backlight

DOWN

Enter

UP

6.

7.

8.

9.

10.

Air/Fuel Ratio

Voltage

Vacuum

RPM

Function

WARNING

RPM

VAC

A/F

A/F

VAC

RPM

Please must follow all installations in this manual to ensure safe installation and operation
of the product. DO NOT disassemble or reassemble the product. This might cause damage
or make them unsafe to use. When the product is disassembled or reassembled, the
Warranty can't be offered. Before installation, please make sure the engine is switched off
and the vehicle is stationary. Due to possible injury from contact with a hot engine or
exhaust pipe, DO NOT begin installation until the vehicle is cool. When attaching wires for
the product, please take care so that the product's wires do not interfere with existing
wires. This product is only for use on vehicles with 12V electronic system.

Backlight LED Setting Function

1. Select icon by press

to enter Oil Pressure Setup Mode.

2. Press

to show Oil Pressure Warning Value. Then Press

or

to change the setting.

3. Press

to save or idle any button for 5 seconds to leave the setting mode.

1. Select icon by press

to enter Oil Pressure Setup Mode.

2. Press

to show Oil Pressure Peak Value. Then press

to clear the Peak Value.

3. Press

to save or idle any button for 5 seconds to leave the setting mode.

Press

to Enter Peak Setup Mode.

Summary of Contents for Daemon III











Reviews: