Jedo LARK, Manual

USER’S MANUAL

 
1. ASSEMBLING THE STROLLER

The unfolding of the stroller is performed by pulling 
the handle up, when it reaches the correct position, it 
automatically locks in a locking clamp, accompanied by a 
clearly audible „click” sound.

2. ATTACHING AND REMOVING THE WHEELS

To remove rear wheels, press the button on the inside of 
the frame (in front of the brake) (Photo no.1) and remove 
the wheel along with the axle. Repeat for the other side. 
To re-attach, push the button for disengaging the wheels 
and push the wheel axle into the hole in the frame. (Pho-
to no.2). Then release the button and pull them together 
until they lock.
- Install the front 10 „wheel with the fork, by inserting the 
axle forks into the rotary element, until you hear a click of 
the wheel locking into its correct position.
The front wheels may be locked to run straight-ahead 
only, by turning the lock mechanism of wheels located on 
both sides of the frame, under the footrest (Photo no.4) 
to the left (looking from the handle) until it clicks. 
To remove the front wheel, press the gray button on the 
inside of the frame, just below the rotary element locking 
the front wheels (Photo no.3)

WARNING!

 The wheels are covered with a lubricant, 

which may stain textiles.

3. ENGAGING THE BRAKES

The stroller is stopped by pressing the brake pedal, posi-
tioned at the right wheel (handle side – Photo no. 5). 
Release the brake by pushing the identical brake pedal, 
positioned at the left wheel.

4. ASSEMBLY / REMOVAL OF THE CARRY COT.

Assemble the carry cot on the chassis by inserting the 
plastic carry cot adapters, located in its lower part, 
into the central locking mechanism. Locking will occur 
automatically. To remove the carry cot, press buttons 
simultaneously on both sides of the carry cot (Photo 
no.6), then lift the carry cot up.

WARNING!

 Before use, check if the carry cot is properly 

locked in the central locking mechanism.

5. INSTALLATION OF THE FOOT COVER

Put the foot cover on the carry cot and fasten using the 
press-studs on the sides of the hood and the cover. 
- The „T” line extendable cover element must be clipped 
to the booth by means of magnets in its interior. 
- The „R” line extendable cover element may be clipped 
to the booth with a magnet located at the top of the hood, 
under the sun-roof.

6. ADJUSTING THE BACKREST OF THE CARRY COT 

Adjusting the backrest is done by means of a regulating 
element, positioned underneath the carry cot, at the level 
of the backrest (Photo no. 7). To raise the backrest, gen-
tly press the element and lock the backrest in the desired 
position, by moving it forward or backward.

7. THE ROCKER FUNCTION OF THE CARRY COT

To use the carry cot’s rocker function, move the two roc-
ker elements located at the bottom of the carry cot from 
the horizontal position to the vertical position (Photo no. 
8 a,b).

8. SETTING THE CARRY COT VENTILATION 

To change the carry cot ventilation, move the ventilation 
control located on the bottom of the carry cot to the right 
or to the left (Photo no. 9).

9. REMOVAL OF THE CARRY COT

To remove the carry cot, remove the material inside the 
carry cot to reveal the hidden mechanism of the carry 
cot (Photo no. 10), then move the 4 folding mechanisms 
towards the center part of the carry cot (Photo no. 11). 
To remove the carry cot, the mechanisms must be moved 
to their folding position.

10. SEAT ASSEMBLY (STROLLING INSERT)

The seat assembly and disassembly is performed similar 
to the carry cot, with two buttons located on both sides 
of the seat. The seat can be installed in two ways - facing 
forward or rearward.

WARNING!

 Do not carry the seat by grasping the 

footrest!

WARNING! 

Before use, check if the seat is properly 

locked in the central latch.

WARNING

! Before using the stroller, always check whe-

ther the backrest is properly locked.

11. INSTALLATION / REMOVAL OF SEATS HOOD

The seat is equipped with its own hood, in order to 
mount it on the seat, insert the plastic hood-fastening 
elements located at the ends of the rod (Photo no.12) 
into plastic connectors located on both sides of the 
backrest. (Photo no. 13). To remove the hood, press the 
button on the hood-fastening element, then pull the rod 
upwards.

12. INSTALLATION / REMOVAL / RAIL HEIGHT ADJU-
STMENT

Mount the safety rail by placing the element for rail 
mounting in the connectors (Photo no. 14). 
In order to remove the rail, press the gray button located 
on both sides of the seat at the height of the rail (Photo 
no.15 A), then pull it towards you. 
To change the height of the rail, press the red button 
(Photo no. 15 B), located on both ends, then set the desi-
red height of the railing. Locking in the selected position 
happens automatically.

13. ASSEMBLY OF FEET COVER (Seat)

Stretch cover on the seat and attach using press-studs.

14. ADJUSTING THE BACKREST OF THE SEAT.

The backrest of the seat can be set in several positions. 
To lower the backrest, pull the plastic regulation element 
located in the rear of the backrest, then set the correct 
position. (Photo no.16)
WARNING!! The same button is used to fold the seat in 
half; in order to do that, press the button described above 
a little longer and move the backrest of the sear toward 
the front. This operation is performed after prior disman-
tling of seat hood (not applicable to the R line).  
To raise the backrest, simply push it upwards until you 
reach the correct position. Locking will occur automati-
cally.

15. SETTING THE FOOTREST POSITION / ADJUSTING 
THE LENGTH 

The footrest can be adjusted in several positions. To 
lower it, press the two buttons located on both sides of 
the footrest and gently lower it down. (Photo no. 17).