If desired, a second memory profile can be stored
into memory as follows:
1. Turn the ignition ON.
2. Adjust all memory profile settings to desired
preferences (i.e., seat, side mirror, and radio
station presets).
3. Press and release the SET (S) button on the
memory switch, then press the side of the rocker
switch labeled (2) within five seconds. The EVIC, if
equipped, will display which memory position is
being set.
NOTE:
•
For vehicles equipped with an automatic
transmission, memory profiles can be set
without the vehicle in PARK, but the vehicle
must be in PARK to recall a memory profile.
•
For vehicles equipped with a manual trans-
mission, the vehicle speed must be at 0 mph
(0 km/h) to recall a memory profile.
•
The Recall Memory with Remote Key Unlock
feature can be turned on and off through the
EVIC, if equipped. For details, refer to “Per-
sonal Settings (Customer Programmable
Features)” under “Electronic Vehicle Infor-
mation Center (EVIC)” in Section 4 of this
manual.
Linking and Unlinking the Remote
Keyless Entry (RKE) Transmitter to the
Memory Feature
Your RKE transmitters can be programmed to
recall one of two pre-programmed memory pro-
files with a press of the UNLOCK button on the
RKE transmitter.
To program your RKE transmitters, perform the
following:
1. Remove the key from ignition.
2. Select the desired memory profile 1 or 2.
3. Press and release the SET (S) button on the
memory switch, then within five seconds press
and release the side of the rocker switch labeled
1 or 2 accordingly.
"
Memory Profile Set” (1 or 2)
will display in the EVIC, if equipped.
4. Press and release the LOCK button on the RKE
transmitter within 10 seconds.
NOTE:
Your RKE transmitters can be unlinked to the
memory setting by pressing the SET (S) button
followed by the UNLOCK button on the RKE
transmitter in Step 4 above.
Memory Position Recall
NOTE:
•
For vehicles equipped with an automatic
transmission, the vehicle must be in PARK
to recall memory positions. If a recall is
attempted when the vehicle is not in PARK, a
message will display in the EVIC, if
equipped.
•
For vehicles equipped with a manual trans-
mission, the vehicle speed must be at 0 mph
(0 km/h) to recall memory positions. If a
recall is attempted with the vehicle speed
above 0 mph (0 km/h), a message will dis-
play in the EVIC, if equipped.
To recall the memory settings for driver one, press
memory button number 1 or the UNLOCK button
on the RKE transmitter linked to memory position
1.
To recall the memory setting for driver two, press
memory button number 2 or the UNLOCK button
on the RKE transmitter linked to memory position
2.
A recall can be cancelled by pressing any of the
memory buttons (S, 1, or 2) during a recall. When
a recall is cancelled, the driver seat will stop
moving. A delay of one second will occur before
another recall can be selected.
68
Summary of Contents for Cherokee 2009
