background image

Jeff Rowland Design Group, Inc. strives to manufacture the very finest possible equipment and 
therefore reserves the right to make changes in design and improvements upon its previously 
manufactured models.

THE ABOVE WARRANTY IS THE SOLE WARRANTY GIVEN BY JEFF ROWLAND DESIGN GROUP, 
INC. AND IS IN LIEU OF ALL OTHER WARRANTIES; ALL IMPLIED WARRANTIES OF 
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE SHALL BE STRICTLY LIMITED 
IN DURATION TO FIVE YEARS FROM THE ORIGINAL DATE OF PURCHASE AND UPON THE 
EXPIRATION OF THIS FIVE YEAR WARRANTY PERIOD, JEFF ROWLAND DESIGN GROUP, INC. 
SHALL HAVE NO FURTHER OBLIGATION OF ANY KIND WH ETHER EXPRESSED OR IMPLIED. 
SOME STATES DO NOT ALLOW EXCLUSIONS OR limitation ON HOW LONG IMPLIED 
WARRANTIES LAST, IN WHICH CASE THE ABOVE LIMITATIONS SHALL NOT APPLY. 

Jeff Rowland Design Group, Inc. does not authorize any third party, including any dealer or 
representative, to assume any liabilities on its behalf or to make any warranties on its behalf 
unless authorized to do so.

Warranty registration cards must be completed and mailed to Jeff Rowland Design Group, Inc. 
within thirty (30) days of the date of purchase. If this product is used in a commercial or 
industrial application, then special warranty exclusions may apply. Contact your dealer or Jeff 
Rowland Design Group, Inc. for information regarding our commercial warranty policies.

GUIDE USE

This guide is designed to make installing and using this product as easy as possible. 
Information in this document has been carefully checked for accuracy at the time of printing; 
however, Jeff Rowland Design Group, Inc.'s policy is one of continuous improvement, therefore 
design and specifications are subject to change without prior notice. If you notice any errors 
please feel free to email us at: support@jeffrowlandgroup.com.

This document contains proprietary information protected by copyright. All rights are 
reserved. No part of this manual may be reproduced by any mechanical, electronic or other 
means, in any form, without prior written permission of the manufacturer. All trademarks and 
registered trademarks are the property of their respective owners.

© Copyright Jeff Rowland Design Group, Inc 2011

 

PAGE  3

Summary of Contents for 625














Reviews: