background image

 

NOTE FROM JEFF ROWLAND DESIGN GROUP 

 

elcome to the Jeff Rowland Design Group “family” and congratulations 
on your purchase of what is unquestionably one of the world’s finest 
amplifiers. With its combination of features such as precision electronic 

circuitry, exceptional efficiency, and accurately machined chassis components 
throughout, your 

MODEL 735 MONOBLOCK AMPLIFIER

 

will offer you many years of 

musically satisfying enjoyment.
Please take a few minutes to read the remainder of this Owner’s Manual before 
proceeding with the installation of the amplifier. A thorough understanding of the 
operational features will allow you to gain the maximum performance and ease of 
use for which this amplifier was designed. 
Please note that your 

MODEL 735 MONOBLOCK AMPLIFIER

 serial number begins with 

the letters “SD”. Please include this number with any correspondence regarding 
your 

MODEL 735 MONOBLOCK AMPLIFIER

. It has been my joy to create an audio 

component of enduring value that reflects the highest ideals of musical and 
artistic expression. It is my hope that these qualities will enrich your experience 
and pride of ownership.
If you have any additional questions regarding the installation or operation of the 

MODEL MODEL 735 MONOBLOCK AMPLIFIERS

, please contact your authorized Jeff 

Rowland Design Group dealer or check the Jeff Rowland Design Group web site 
at 
http://jeffrowlandgroup.com.
Enjoy the music!

Je

 Rowland 

President, Je

 Rowland Design Group 

PAGE   4

W

Summary of Contents for 735














Reviews: