background image

The crossed-out wheeled bin is the European Union symbol for 
indicating separate collection for electrical and electronic equipment. 
This product contains electrical and electronic equipment which 
should be reused, recycled or recovered and should not be 
disposed of with unsorted regular waste. Please return the unit or 
contact the authorized dealer from whom you purchased this 
product for more information.

This product complies with European Low Voltage (2006/95/EC) and 
Electromagnetic Compatibility (89/336/EEC) Directives when used 
and installed according to this instruction manual. For continued 
compliance servicing must be referred to qualified service 
personnel.

LIMITED WARRANTY

Je

 Rowland Design Group, Inc. warrants the materials, workmanship, and proper functioning 

of this product for a period of 

fi

ve years from the date of purchase as long as the product was 

operated in accordance with its operating manual, the products was not altered or improperly 
serviced or prepared, or if the product failed to function from the beginning. In the event of 
such a failure, the product will be repaired or replaced by Je

 Rowland Design Group, Inc. 

through one of its dealers. This warranty is extended to the original purchaser only and is non-
transferable to any secondary or other purchaser. 

In order to have this product repaired or replaced, the original purchaser must 

fi

rst obtain the 

prior authorization of Je

 Rowland Design Group, Inc. or one of its dealers. Purchaser must 

then return the product, PACKAGED IN ITS ORIGINAL CARTON, FREIGHT PREPAID to: Je

 

Rowland Design Group, Inc., 2911 North Prospect Street, Colorado Springs, Colorado, 80907, or 
to one of its dealers.

Je

 Rowland Design Group, Inc. reserves the right to inspect any product which is subject to 

any warranty claim prior to repairing or replacing it. Final determination of warranty coverage 
lies solely with Je

 Rowland Design Group, Inc. Said determination shall be made as soon as 

possible following receipt of the product. Je

 Rowland Design Group, Inc. may, at its option, 

require from the purchaser, valid proof of purchase (dated copy or photocopy of dealer's 
original invoice). Out-of-warranty claims will be billed for labor, materials, return freight, and 
insurance as required. Any product for which a warranty claim is accepted will be returned to 
the purchaser and costs of shipping and insurance will be factory prepaid within the 
boundaries of the USA. Units to be shipped outside of the USA will be shipped freight collect 
only. This warranty gives the holder speci

fi

c legal rights. The purchaser also has implied 

warranty rights, and may also have other rights which may vary from state to state.

 

REVA1.9 - CONTINUUM S2 INTEGRATED AMPLIFIER

 

 PAGE  2

Summary of Contents for CONTINUUM S2






















Reviews: