background image

 

 

Installation Instructions for 555-79006 
4 Ton Bottle Jack 

 

CAUTION:  Before using this product, read this manual and follow all 

Safety Rules and Operational Instructions. 

 

SPECIFICATIONS 

Capacity  

Lift Range 

  

4 Ton (8000 lbs.) 

8.15"-13.58" 

  

  

8.15"-16.02" with screw extension 

 
 

Owner and/or Operator Responsibility 

The owner and/or operator shall read, study and understand the product instructions and retain them 
for future reference.   
 

Operation 

The owner and/or operator shall have an understanding of the product and safety operating 
instructions before operating the product. Safety information shall be emphasized and understood. If 
the operator is not fluent in English, the product warnings/cautions and instructions shall be read to and 
discussed wi

th the operator in operator’s native language by purchaser/owner or his designee, insuring 

that the operator comprehends their content. 
 

Inspection 

(a)  Visual inspection MUST be made prior to each use of the jack. Check for cracks, cracked 

welds, missing or damaged parts.  

(b)  Keep all moving parts clean and well lubricated. 
(c)  Owners and/or operators should be aware that repair of this equipment may require specialized 

knowledge and facilities. It is recommended that an annual inspection of the product be made 
by a m

anufacturer or supplier’s authorized repair facility and that any defective parts, decals, or 

safety labels and signs be replaced with manufacturer or supplier’s specified parts.  

 

Damaged Equipment 

Any jack that appears to be damaged in any way or is found to be worn or operates abnormally SHALL 
BE REMOVED FROM SERVICE IMMEDIATELY UNTIL REPAIRED. It is recommended that a 
manufacturer or supplier’s authorized repair facility make necessary repairs if the manufacturer or 
supplier permits repairs 
 

Alterations 

Because of potential hazards associated with the misuse of equipment of this type, NO 
MODIFICATIONS/ALTERATIONS shall be made to the product.  
 

Attachments and Adaptors 

Only attachments and/or adaptors supplied by the manufacturer shall be used. 

 

                                         1-800-345-4545   jegs.com

 

Summary of Contents for 555-79006






Reviews: