background image

Installation Instructions Product-Ident: 75181

Doorboards include speakers, Audi A3 8P - 2-türig

Technical Details:

Car Features:

electrical window controls, only 2-doors

Model/Year:

8P (05.2003)

Door Dampening:

recommended - see attached installation

recommendation

Setup-Advice:

To reach the best performance, the setup of the

radio (Bass, Loudness etc.) should be null or

neutral.

recommended amplifier power:

from 2x 150 - 300 Watt / 4 Ohm

Metal cutting:

not applicable

Parts list:

1x

Doorboards (right+left) Audi A3 8P, covered

1x

grills (right+left) Audi A3 8P, cover: acoustic fabric

2x

XE 26 - Neodymium-Tweeter ø 26mm (1")  incl. mounting device, Hex nut M4, washer ø 12mm

2x

XM 110 - High-End-midrange driver, ø 100mm (4"),  incl. adapterring

8x

XM 165 - Low midrange driver, power woofer ø 165mm (6,5")

1x

serial wire set for woofers (right + left)

2x

3-way frequency crossover (right+left) Audi A3 -2-door only - part-no. 75181

1x

Hardware bag, Audi A3 -2-door only - part-no. 75181/71181

8x

 flat head srew M4 x 30

2x

 flat head srew M4 x 40

2x

 flat head srew M4 x 50

22x

 hex nut M4

4x

 Velcro strip à 2,5 cm (reserve)

4x

 washer 12mm

18x

 washer 20mm

Garantee:

We grant a manufacturers guarantee of 2 years starting from the date of purchase of the doorboard or sound system from the dealer. Within this
guarantee period to our choice we either repair or replace free of charge all defects due to material or workmanship. Exempt from this guarantee
are damages due to improper use, wear and tear or damages which have to be led back on wear or interventions by third parties. The guarantee
does not cover subsequent damages or such defects that only insignificantly impair the value or the usability of the doorboard/sound system. The
guarantee does not cover damages due to external influences. Doorboards with additional or wrong assembly drill holes cannot be returned. These
are damages to the doorboard which cannot be repaired again.

Summary of Contents for 75181











Reviews: