background image

ZR12-AL USER GUIDE

Introduction

The ZR12 is the first small JEM machine to feature the new “AL” Analogue

Link technology. This allows units to be linked together and controlled from one

JEM Multi Function Controller. The ZR12 is also fitted with a 1 kW heat

exchanger which guarantees the maximum output from this size of vaporizing

system.

The ZR12 uses the ‘DTP’ overheat protection device for the best possible

overheat protection. This was first used on the JEM

with great

success. A 2.5

fluid container is supplied to minimize the need for refilling.

A multi-function controller enables the user to operate the machine manually

using the ‘FOG’ button or set the timer for auuotmatic operation. The timer has

a new feature called x8 mode, this allows the timer values to be adjusted from x1

to x8 giving the user more variation in the timer settings. There is also a ducting

kit for applications where the effect is needed in an area away from the ZR12

Features:

Analogue Link facility

High Power Piston Pump

Multifunction Remote Controller

“DTP” Safety System

Pump Ramping For Continuous Output

2.5 Litre Fluid Capacity

SMD Electronics

Low Noise Soft Start Pumping

Heavy Duty Construction

TECHNO-FOG

.

Litre

PAGE 2

MARTIN MANUFACTURING (UK) PLC

ZR12-AL USER GUIDE

Notes

PAGE 11

MARTIN MANUFACTURING (UK) PLC

Summary of Contents for ZR12-AL









Reviews: