Jema Autolifte JA2800S Installation, Operation And Maintenance Manual Download

Page: 5 / 17

WE ARE HERE TO SURPRISE!

2.2 Technical data

Model

Lifting capacity

Lifting time Lifting height

Electrical requirement

JA2800S

2800kg

50 Sec

1200mm

220V/240V, Single Phrase

Weight of JA2800S = 415 KG.

2.3 Construction of the lift

3. Installation instructions

3.1 Preparations before installation
3.1.1 Tools and equipments needed

√ Electrical drill

√ Open wrenches

√ Screw drivers

√Adjustable spanner

3.1.2 List for checking of parts ---Annex 1 (Packing list)

Unfold the package and check if any parts missed as per Annex 1. Do not hesitate to contact us in case any parts are missing,

but if you do not contact us and insist on installing the lift lacking of some parts, Jema A/S as well as our dealers will not bear

any responsibility for this and will charge for any parts subsequently demanded by the buyer.

Summary of Contents for JA2800S


















Search results

Summary of Contents for JA2800S

Reviews:

Related manuals for JA2800S

Brands by name

Popular brands

Jema Autolifte JA2800S, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for JA2800S

Reviews:

Related manuals for JA2800S

Brands by name

Popular brands