background image

 

 

3.3 Installation instructions   

Step1: Choose a proper site   

Location requirement   

If not specifically stated, our lifts are only for indoor use. It should be fixed on a smooth and solid concrete ground. Do not install 

this lift on expansion beams of concrete or on a second or an elevated floor without first consulting building architect.

 

Make sure 

that the space around or over the lift should be free of obstructions like heaters, building supports, electrical lines etc.

 

Step 2: Fix the installation layout   

Once the installation site is determined, mark first the standing point of the four posts by a tape measure and chalk. Ensure two 

diagonal lines are of the same length.   

Step 3: Remove the packing materials   

1.  Place some wooden battens on the ground and then use a crane to have the packing rack removed on to the battens so as to 

make its base is of some clearance from the ground. 

2.  Have the platforms of the lift suspended by a crane and then screw off the upside bolt and remove the first platform on to the 

wooden battens initially prepared.   

3.  Screw off the downside bolt and take away the packing rack on both sides. 

4.  Remove the shock absorption plastic film with a knife. 

Step 4: Use a crane to have the general parts positioned in accordance with following layout.   

For convenient installation, it would be better to pad something supporting under the platform.   

Oil cylinder, steel cable and oil hose have already been fixed in the main platform before packing. 

Wires rope, oil hose, safety lock etc, have already been fixed in the beams before packing. 

 

Step5: Connect the platforms and beams   

Firstly, connect the main beam with two platforms. Align accurately the screw sockets on the platform and the beam. Installers can 

adjust  the distance  between  two  platforms  on  basis  of  practical  needs.  Once  the  distance  was  adjusted,  fasten  the  beam  and 

platforms with M12*30 hex bolt with spring and flat washer padded.    Connect the other beam in the same way. 

Summary of Contents for JA5500F





































Reviews: