JENN-AIR
®
DETAILED PLANNING DIMENSIONS
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
2 of 4
7778AdZw613
E*
L
N
P
O
F
D
e
A
B
B
M
v
v
C
J**
H
G
M
Side
Cabinet
C
K
I
E*
L
N
P
O
F
D
e
A
B
B
M
v
v
C
J**
H
G
M
Side
Cabinet
C
K
I
E*
L
N
P
O
F
D
e
A
B
B
M
v
v
C
J**
H
G
M
Side
Cabinet
C
K
I
30" JX3™ GAS DOWNDRAFT COOKTOP
JGD3430B – 30" x 18
3
⁄
8
" x 21
1
⁄
2
"
MODEL #
JGD3430B
in
cm
A
Width of combustible area above cooking
surface (min.)
30
76.2
B
Width from cooktop to fixed wall or other
combustible material (min.)
6
15.2
C
Width to center of vent opening option
8
1
⁄
2
21.6
D
Width to outer edge of outlet
10
25.4
E*
Height to bottom of uncovered wood or metal
cabinet above cooking surface (min.)
30
76.2
F
Height to bottom of uncovered wood or metal
cabinet (min.)
18
45.7
G
Height to center of vent opening option
16
40.6
H
Height to top edge of outlet (min.)
12
30.5
I
Height to top of gas installation area
6
15.2
J**
Depth to center of vent opening option
17
1
⁄
8
43.5
K
Depth of gas installation area
6
15.2
L
Depth of upper cabinet (recommended)
13
33.0
M
Depth from cutout to wall (min.)
2
5.1
N
Width of cutout
28
5
⁄
8
72.7
O
Depth of cutout
20
50.6
P
Depth from cutout to front of countertop
2
1
⁄
8
5.4
e
Recommended electrical access location
g
Recommended gas supply line location
v
Recommended venting location –
see pages 3-4 for ducting information
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal
cabinet is covered by not less than
1
⁄
4
" (0.6 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless
steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
**Based on installation in a 24" deep (61.0 cm) base cabinet.
OPENING/CLEARANCE DIMENSIONS
FRONT VIEW
SIDE VIEW
TOP VIEW
GAS REQUIREMENTS
Natural Gas
This cooktop is factory-set for use with natural gas.
LP Gas Conversion
Conversion must be done by a qualified service technician. To convert to LP gas, use
the LP gas conversion kit provided with the cooktop.
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required. A time-delay
fuse or dedicated circuit is recommended.
VENTING REQUIREMENTS
This cooktop must be exhausted outdoors unless using the duct-free filter kit
(JDA7000WX). Refer to kit instructions for further information.
LOCATION REQUIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider than the cutout.
• A minimum clearance of 2" (5.1 cm) is recommended between the blower motor and
cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for servicing access.
• An under counter built-in oven cannot be installed under this cooktop.
