10
To Remove and Replace the Ice Bin:
1.
Flip up the covering panel.
A
A. Ice maker cover
2.
Lift the wire shutoff arm so it clicks into the OFF (up) position.
Ice can still be dispensed, but no more can be made.
3.
Lift up the front of the storage bin and pull the ice bin forward.
4.
Replace the bin by pushing it in all the way or the dispenser
will not work. Push the wire shutoff arm down to the ON
position to restart ice production. Make sure the door is
closed tightly.
Style 2
To Turn the Ice Maker On/Off:
The On/Off switch is located on the top right side of the freezer
compartment.
1.
To turn the ice maker on, slide the control to the ON (left)
position.
NOTE:
Your ice maker has an automatic shutoff. The ice
maker sensors will automatically stop ice production, but the
control will remain in the ON (left) position.
2.
To manually turn the ice maker off, slide the control to the OFF
(right) position.
To Remove and Replace the Ice Storage Bin:
1. Hold the base of the storage bin with both hands and press
the release button to lift the storage bin up and out.
NOTE:
It is not necessary to turn the ice maker control to
the OFF (right) position when removing the storage bin. The
sensor cover (“flipper door”) on the left wall of the freezer
stops the ice maker from producing ice if the door is open or
the storage bin is removed.
2. Replace the storage bin on the door and push down to make
sure it is securely in place.
Clean the Ice Storage Bin
NOTE:
It is normal for ice to stick together in the ice bin. Ice may
be dispensed or used more frequently which will break up the ice.
It is recommended that the ice container be emptied and cleaned
as needed.
To clean the ice storage bin:
1.
Empty the ice container. Use warm water to melt the ice if
necessary.
NOTE:
Do not use anything sharp to break up the ice in the
bin or bucket. This can cause damage to the ice container
and the dispenser mechanism.
2.
Wash ice bin with a mild detergent, rinse well and dry
thoroughly. Do not use harsh or abrasive cleaners or solvents.
Remember
■
Allow 24 hours to produce the first batch of ice. Allow 3 days
to completely fill ice container.
■
Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.
■
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.
■
Avoid connecting the ice maker to a softened water supply.
■
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
■
It is normal for the ice cubes to be attached at the corners.
They will break apart easily.
■
For
Style 1
ice maker, do not force the wire shutoff arm up or
down.
■
Do not store anything on top of the ice maker or in the ice
storage bin/bucket.
Water Filtration System
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.
Water Filter Indicator (on some models)
The water filter indicator, located on the control panel, will help
you know when to change the water filter.
A new water filter should display a reading of 99%. The reading
in the display will decrease as the filter life is used. A replacement
water filter should be ordered when “Order Filter” is displayed. It
is recommended that you replace the filter when “Change Filter”
is displayed or when water flow to your water dispenser and/or
ice maker decreases noticeably. See “Changing the Water Filter”
later in this section.
NOTE:
Dispenser models have a filter reset on the freezer
compartment door. Non-Dispenser models have a Good/Order
Filter/Replace Filter indicator.
After changing the water filter, press and hold RESET for
2 seconds until the status display changes to 99%.
