WARNING
!
To avoid risk of electrical shock, personal injury or death;
disconnect power to unit before servicing.
Disassembly Procedures
©2004 Maytag Services
16022882 Rev. 0
21
Selector Switch
1. Remove control panel, see “Control Panel” procedure.
2. Remove screws securing landing ledge on each side
of landing ledge.
3. Unscrew selector switch from the bracket.
4. Remove screws securing top of bracket.
5. Disconnect and label wire terminals to selector switch.
6. Reverse procedure to reassemble.
Hinge Receptacle
1. Remove oven door, see “Oven Door” procedure.
2. Remove lower screw on receptacle completely.
3. Secure center of receptacle and remove top screw
completely.
NOTE:
Failure to secure hinge, will result in receptacle
falling inside oven chassis.
4. Once both screws have been removed, the hinge
receptacle can be removed through the front.
• Start by pushing in on the top and rotating in
enough to get the bottom of the receptacle out of
the hole.
Hinge Installation
NOTE:
Verify roller is located on the top of the hinge.
1. Place hinge into receptacle hole.
2. Loosely tighten top screw on hinge receptacle.
NOTE:
Do not fully tighten screw at this time.
3. Place gasket guard into place.
4. Secure bottom screw through the gasket guard and
into the hinge receptacle.
5. Tighten both screws securely and reinstall door.
Door Hinge
1. Remove oven door, see “Oven Door” procedure.
2. Remove all torx screws securing top of door skin.
3. Remove all stainless steel screws securing bottom of
door skin.
4. Place door skin to the side, ensuring not to damage it.
5. Release tension on hinge for removal from door, by
compressing the hinges together and releasing copper
clip.
WARNING
!
To avoid personal injury or product damage, releasing
tension on hinge spring before removing.
6. Remove screws securing each hinge to door liner.
NOTE:
For replacement, door hinge needs to be
compressed together again for proper door
installation.
Door Window Pack
1. Remove door hinge, see “Door Hinge” procedure.
2. Remove screws securing compression brackets to
insulation retainer.
3. Remove screws securing top of insulation retainer and
remove.
4. Remove insulation and place to the side, taking care
not to damage insulation.
5. Remove nuts securing window pack in place.
6. Reverse procedure to reassemble.
NOTE:
When reassembling window pack, ensure proper
placement of insulation.
Door Gasket
1. Remove door gasket, by gently pulling the ends of the
gasket out of the oven bottom front.
2. Release clips by squeezing metal clip together to
remove out of the oven front frame.
NOTE:
Oven door can be removed for easier
replacement.
Installing Door Gasket
1. To install new gasket, start at one of the top corners
where there are three holes in a row.
NOTE:
The gasket will have three clips closely spaced
together to correspond with those holes.
2. Start with the three closest spaced clips and insert the
center clip in the center hole of the corner.
3. Work around the oven cavity gently pushing clips in.
NOTE:
Verify the clips click into the holes, ensuring that
they seat correctly in the hole.
4. Once all clips have been installed. Inserted the ends of
the gasket into the holes under the oven bottom
center, leaving an ½” gap between the two ends.
Oven Door
1. Open oven door to the fully opened position.
2. Secure hinge lock by sliding copper clip on lower
hinge over the finger located on the underside of the
top hinge.
3. While holding the oven door securely, start to close
the door and gently lift upward and outward to
disengage hinges from receptacles.
Reinstalling Oven Door
•
After oven door is placed on hinge receptacles, the
door will make a clicking noise when closed for the
first time, indicating the oven door is properly aligned
NOTE:
In the event that the oven door is off of the oven
and hinges are not closed together, the hinges
will need to be compressed and copper clip
needs to be closed.
