Jenn-Air PRO-STYLE JGRP430W, Installation Instructions Manual

4

Parts needed

All models must be installed with a backguard if installing at zero 
clearance to a combustible backwall. See “Cabinet Dimensions” in 
the “Location Requirements” section for installation requirements.

■

30" (76.2 cm) Adjustable Backguard
Order Part Number 8285148

■

36" (91.4 cm) Adjustable Backguard
Order Part Number 8284756

■

48" (121.9 cm) Adjustable Backguard
Order Part Number 8284755

■

22" (55.9 cm) Backsplash with Dual-Position Shelf for 
30"(76.2 cm) Ranges
Order Part Number W10285447

■

22" (55.9 cm) Backsplash with Dual-Position Shelf for 
36" (91.4 cm) Ranges
Order Part Number W10285448

■

22" (55.9 cm) Backsplash with Dual-Position Shelf for 
48" (121.9 cm) Ranges
Order Part Number W10285449

To order, see the “Assistance or Service” section of the Use 
and Care Guide.

Check local codes and consult gas supplier. Check existing gas 
supply and electrical supply. See “Electrical Requirements” and 
“Gas Supply Requirements” sections.

It is recommended that all electrical connections be made by a 
licensed, qualified electrical installer.

High Altitude Conversion

To convert the range for elevations above 6,560 ft (1999.5 m), 
order a High Altitude Conversion Kit.

■

Part Number W10394294 - LP high altitude

■

Part Number W10394293 - Natural gas high altitude

To order, see the “Assistance or Service” section of the Use and 
Care Guide.

Location Requirements

IMPORTANT:

 Observe all governing codes and ordinances. Do 

not obstruct flow of combustion and ventilation air. 

■

It is the installer’s responsibility to comply with installation 
clearances specified on the model/serial rating plate. The 
model/serial rating plate is located under the console on the 
right-hand side.

■

It is recommended that a 600 CFM or larger range hood be 
installed above the range.

■

It is not recommended that a microwave hood combination 
be mounted above the range.

■

Recessed installations must provide complete enclosure of 
the sides and rear of the range.

■

To eliminate the risk of burns or fire by reaching over heated 
surface units, cabinet storage space located above the 
surface units should be avoided. If cabinet storage is to be 
provided, the risk can be reduced by installing a range hood 
that projects horizontally a minimum of 5" (12.7 cm) beyond 
the bottom of the cabinets.

■

All openings in the wall or floor where range is to be installed 
must be sealed.

■

Do not seal the range to the side cabinets.

■

Cabinet opening dimensions that are shown must be used. 
Given dimensions are minimum clearances.

■

The anti-tip bracket must be installed. To install the anti-tip 
bracket shipped with the range, see “Install Anti-Tip Bracket” 
section.

■

Grounded electrical supply is required. See “Electrical 
Requirements” section. 

■

Proper gas supply connection must be available. See “Gas 
Supply Requirements” section.

■

Contact a qualified floor covering installer to check that the 
floor covering can withstand at least 200°F (93°C). Use an 
insulated pad or ¼" (0.64 cm) plywood over carpet and under 
range if installing range over carpeting.

IMPORTANT:

 To avoid damage to your cabinets, check with your 

builder or cabinet supplier to make sure that the materials used 
will not discolor, delaminate or sustain other damage. This oven 
has been designed in accordance with the requirements of UL 
and CSA International and complies with the maximum allowable 
wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured 
Home Construction and Safety Standard, Title 24 CFR, Part 3280 
(formerly the Federal Standard for Mobile Home Construction 
and Safety, Title 24, HUD Part 280). When such standard is not 
applicable, use the Standard for Manufactured Home 
Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the 
current standards CAN/CSA-A240-latest edition, or with local 
codes.

Mobile home installations require:

■

When this range is installed in a mobile home, it must be 
secured to the floor during transit. Any method of securing 
the range is adequate as long as it conforms to the standards 
listed above.

Product Dimensions

30" (76.2 cm) models

A. Island trim
B. 27¾" (70.5 cm) depth with control panel, see NOTE*

C. 35¾" (89.6 cm) cooktop height when setting on the wheels
D. 30" (76.2 cm) width

E. Model/serial rating plate location

B

C

E

D

A