5
4. Slide the compression nut over the sleeve and screw into the
water valve inlet port.
5. Using an adjustable wrench, hold the nut on the plastic water
line to keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise
to completely tighten. Do not overtighten.
6. Check connection by pulling on copper tubing. Attach the
plastic water line to the refrigerator cabinet with a “P” clamp.
Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Complete the Installation
1. Plug into a grounded 3 prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill the ice container.
Refrigerator Door(s) and Drawer
TOOLS NEEDED:
⁵⁄₁₆
",
³⁄₈
",
¹⁄₄
" hex head socket wrench, a
#2 Phillips screwdriver, and a flat-blade screwdriver.
IMPORTANT:
■
Your refrigerator may have a standard reversible refrigerator
door (Style 1) with either a freezer door or freezer drawer, or
French doors (Style 2). Follow the instructions specific to the
door style of your model.
■
All graphics referenced in the following instructions are
included later in this section after “Final Steps.” The graphics
shown for the standard door (Style 1) are for a right-hand
swing refrigerator (hinges factory installed on the right).
■
If you only want to remove and replace the doors, see
“Remove Door(s) and Hinges” and “Replace Door(s) and
Hinges.”
■
Before you begin, turn the refrigerator control OFF, and
remove food and adjustable door or utility bins from the doors.
Remove and Replace Refrigerator Door Handles
Style 1–Standard Door
Front Mount Handle
■
To remove the handle, remove the screw attaching the trim to
the upper end of the handle. Using a flat-blade screwdriver
wrapped in masking tape, pry the trim piece from the lower
end of the handle. Then, remove the screws attaching the
handle to the door. See Front Mount graphic 2.
■
To replace handle, reverse directions.
Side Mount Handle
■
To remove the handle, remove the four screws attaching the
handle to the side of the door. See Side Mount graphic 2.
■
To replace the handle, align the holes in the handle with the
holes in the door. Then, insert a screw into the upper hole at
each end of the handle. Next, insert a screw into the lower
holes. Tighten the screws. See Side Mount graphic 2.
Style 2–French Doors
Metal Handles
■
Using a
³⁄₃₂
" or
¹⁄₈
" Allen wrench, loosen the two setscrews
located on the side of each handle. Pull the handle straight out
from the door. Make sure you keep the screws for reattaching
the handles. See Metal Handle graphic 1.
■
To replace the handles, reverse the directions.
Plastic Handles
■
To remove the handle, grasp the lower part of the handle
firmly, slide the handle up and pull the handle straight out from
the door. See Plastic Handle graphic 1.
■
To replace the handle, position the handle so that the large
holes in the mounting clips are down and align the holes with
the door studs. Rotate the handle so that the mounting clips
are flat against the door and slide the handle down to engage.
See Plastic Handle graphic 1.
Remove Door and Hinges
Style 1–Standard Door
A. Plastic water tubing
B. Sleeve
C. Compression nut
D. Copper tubing
A. “P” clamp
B. Plastic water line
C. Water valve inlet port
D. Compression nut
E. Copper tubing
B
A
C
D
C
B
D
E
A
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
⁵⁄₁₆
" Hex-Head Top Hinge Screw
