background image

10

OVEN CARE

Self Cleaning Cycle

WARNING

Burn Hazard

Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during 

Self-Cleaning cycle.
Failure to follow these instructions can result in burns.

IMPORTANT:

 The health of some birds is extremely sensitive to 

the fumes given off during the Self Cleaning cycle. Exposure to 

the fumes may result in death to certain birds. Always move birds 

to another closed and well-ventilated room.
Self clean the oven before it becomes heavily soiled. Heavy soil 

results in longer cleaning and more smoke.
Keep the kitchen well-ventilated during the Self Cleaning cycle to 

help get rid of heat, odors, and smoke.
Do not block the oven vent(s) during the Self Cleaning cycle.  

Air must be able to move freely. See the “Oven Vents” section.
Do not clean, rub, damage, or move the oven door gasket.  

The door gasket is essential for a good seal.

Prepare Oven:

 

Remove the broiler pan, grid, cookware and bakeware, and, on 

some models, the temperature probe from the oven.

 

Remove oven racks to keep them shiny and easy to slide.  

See the “General Cleaning” section for more information.

 

Remove any foil from the oven because it may burn or melt, 

damaging the oven.

 

Hand clean inside door edge and the 1

1

/

2

" (3.8 cm) area 

around the inside oven cavity frame, being certain not to 

move or bend the gasket. This area does not get hot enough 

during high-temp self cleaning to remove soil. Do not let water, 

cleaner, etc., enter slots on door frame. Use a damp cloth to 

clean this area.

 

Wipe out any loose soil to reduce smoke and avoid damage. 

At high temperatures, foods react with porcelain. Staining, 

etching, pitting, or faint white spots can result. This is normal 

and will not affect cooking performance.

How the Cycle Works

IMPORTANT:

 The heating and cooling of porcelain on steel in the 

oven may result in discoloring, loss of gloss, hairline cracks, and 

popping sounds.
The Self Cleaning cycle uses very high temperatures, burning soil 

to a powdery ash.
Suggested clean times are 1 hour and 15 minutes for light soil,  

1 hour and 40 minutes for medium soil and 2 hours for heavy soil.
Once the oven has completely cooled, remove ash with a damp 

cloth. To avoid breaking the glass, do not apply a cool damp cloth 

to the inner door glass before it has completely cooled.
The oven lights will not work during the Self Cleaning cycle.

NOTE:

 The oven has a two-speed cooling fan motor. During the 

Self Cleaning cycle, the fan(s) will operate at its highest speed to 

increase airflow to better exhaust the hotter air through the oven 

vent(s). An increase in noise may be noticeable during and after 

the Self Cleaning cycle until the oven cools.
Before Self Cleaning, make sure the door is closed completely 

or it will not lock and the cycle will not begin. When the oven 

is locked, the doors of the oven cannot be opened. To avoid 

damage to the doors, do not force the doors open when the oven 

is locked.

1. 

Touch the Settings keypad.

2. 

Select the Self Clean icon.

3. 

Select type of Self Cleaning: 

Light: 1 hour and 15 minutes 

Medium: 1 hour and 40 minutes 

Heavy: 2 hours

4. 

Follow the prompts on the oven display to prepare the oven.

5. 

Select START to begin the cleaning process.

OR

Select DELAY START to set a delayed Self Cleaning cycle. 

See the “To Delay Start Self Cleaning Cycle” Section.
The oven doors will automatically lock.

NOTE:

 It may take a couple moments for the oven door to 

automatically lock after starting the Self Clean Cycle.
When the self cleaning cycle is complete and the oven cools, 

the oven doors will unlock.

6. 

When the oven is completely cooled, remove ash with a damp 

cloth.

To Delay Start Self Cleaning Cycle:

Follow steps 1 through 4 above, then:

1. 

Select DELAY START.

2. 

Select the start time of when the Self Cleaning cycle should 

begin by scrolling from left to right.

3. 

Select START DELAY.
The oven doors will automatically lock after the Delay Start 

countdown.
When the Self Cleaning cycle is complete and the oven cools, 

the oven doors will unlock.

4. 

When the oven is completely cooled, remove ash with a damp 

cloth.

To Stop Self Cleaning Anytime:

Touch the Oven Cancel Keypad. If the oven temperature is too 

high, the door will remain locked. It will not unlock until the oven 

cools.

Summary of Contents for W11260125A

























Reviews: