background image

 

 

12

and listen to it through your wireless speaker system. 

5.) Open the music player program on your computer, and adjust the volume of 

the player program to a low level. 

6). Click the play button, and slowly increase the volume level of your player 

program to adjust the sound level. 

7). Press the /- button on speaker boxes to control the sound level if 

necessary. 

 

Mac Based Computer (for Mac OS X) 

1.) Remove the USB Transmitter from the back of the Docking Base and plug it 

into the USB port of your Mac.   

2.) Go to your computer system preferences and set sound output to “SYNIC 

Wireless Audio” USB device   

3.) Fully charge and place the two speakers within wireless range of the 

transmitter that is plugged into the USB port of your computer. 

4.) Link the wireless speakers by following linking instructions mentioned in the 

“Getting Start” section of the manual. Now you can play music from your Mac 

and listen to it through your wireless speaker system. 

5.) Open the music player program on your computer, and adjust the volume of 

the player program to a low level. 

6). Click the play button, and slowly increase the volume level of your player 

program to adjust the sound level. 

7). Press the /- button on speaker boxes to control the sound level if 

necessary. 

 

SPEAKER BATTERY RECHARGING   

When you remove the speakers from the Docking Base and listen to music 

wirelessly, the built-in rechargeable lithium batteries will eventually reach a low 

power condition. The speaker status red LED will start flashing before it 

switches to solid red and then goes off, so please charge you speaker battery 

immediately when the LED turns to solid red.   

1.    Position the two speakers onto the recessed charging area located on 

the Docking Base. Each speaker has it’s own charging bay.   

2.    The Docking Base LED for each speaker will flash green, indicating that 

the speaker battery is being charged. 

3.    The Docking Base LED for each speaker will turn solid green after 

charging for about 4 - 5 hours in speaker power off mode or once the 

battery is fully recharged.   

Summary of Contents for JiSS-600i



















Reviews: