Jensen JWM70A, Installation And Owner'S Manual

Auxiliary Input Function

Auxiliary Input Connector

USB Interface Connector

Clock Display

Clock Setup

Sleep Mode

Alarm Setting

Remote Sensor

Zones Output

Reset

HDMI ARC

Press the 

AUX

 button (11) to directly access auxiliary input modes (AUX IN1 and 

AUX IN2) from any other mode when a portable audio device is connected to the 
unit. To connect a portable audio device, insert a standard 3.5mm (audio line 
output or headphone output from your portable CD / MP3 / iPod or other media 
player) into the AUX A/V IN connector (AUX IN1) (11) on the front of the unit or 
the AUDIO IN (AUX IN2) on the back of the unit (see

“

Wiring

”

 on page 3).

For front panel A/V input, an external audio/video (A/V) source such as a video 
game player, camera, etc. can be connected to the front panel A/V input with the 
provided 3.5mm A/V cable adapter (Please note that there are several different 
A/V cable "standards"). Connect the device to the AUX A/V IN connector (11) on 
the front panel.
In addition to front panel auxiliary input source, the unit can also be connected 
to the RCA audio input through the AUX AUDIO INPUT jack on the rear of the 
unit.
Press the 

AUX

 button (11) to directly access auxiliary input modes (AUX 1 IN 

and AUX 2 IN) from any other mode when a portable audio device is connected 
to the unit. 

You can connect a USB device directly to USB interface (10) on the front of the 
JWM70A for playback of compatible files. Playback begins automatically. Press 
the USB button (10) to switch to USB mode from another source. Refer to 
“MP3/USB Operation” on page 13 for additional operating instructions. 

Press the 

VIEW 

button (4) to alternate between playing time and clock time while 

in Tuner, CD, DVD, USB or auxiliary input mode.

NOTE: USB will not support Apple device playback. The USB input supplies 
up to 1A of charging current. 

Press and hold the clock 

HOUR

 or 

MINUTE

 button (39, 36) to access clock setup 

mode. The number representing the hours and minutes will flash. Press the 

HOUR

button (39) to adjust the hour and press the 

MINUTE

 button (36) to adjust minutes. 

The new time will be saved five seconds after the last adjustment is made.

The Sleep Timer will automatically turn off the JWM70A in the designated number of 
minutes. To set the Sleep Time, press the 

SLEEP

 button (37) and the sleep time will 

appear in the display with the number representing the minutes (SLEEP 0). Press 

SLEEP

 button repeatedly to change the sleep time from 0 (OFF), 15, 30, 45 or 60 

minutes. 

To set the alarm, press and hold the 

ALARM SET

 button (38) for 2 seconds and the 

clock digits will be flashing. Press the 

HOUR

 button to adjust the hour once at a time 

or press and hold to advance rapidly. Repeatedly press the 

MINUTE

 button to adjust 

the minute one digit at a time, or press and hold to advance rapidly. 
Press the 

ALARM SET

 or 

ENTER 

knob button to save the alarm time. 

Once a time is set, press 

ALARM ON/OFF

 (38) to turn the alarm function on or off.

Infrared receiver is located on the upper left of front panel to receive infrared signal 
emitted by the remote control.

The speaker output button (5) control speaker zones output from the radio. Press the 
buttons to turn the corresponding speaker zone on or off. 

Ÿ

Connect HDMI cable to JENSEN TV with ARC function and JWM70A head unit. If 
the set up and operation is correct, the TV audio will come out from the speaker 
of the head unit after switching to HDMI ARC mode.

Ÿ

See the ARC function Operation in the following table: 

The reset button should be activated for the following reasons:

Ÿ

initial installation of the unit when all wiring is completed 

Ÿ

function buttons do not operate

Ÿ

error symbol on the display

Use a ball point pen or similar object to press the 

RESET

 button (3). This may be 

necessary should the unit display an error code.

8

JWM7

0A