Jensen Mobile Multimedia DVD/MP3/WMA Receiver VM9020TS Operation Manual Download

Page: 12 / 28

VM9020TS

OPERATING INSTRUCTIONS

Power On / Off

Press the

/MUTE

button (1) to turn the unit on. The buttons

on the front of the unit will light up.

Press and hold

the

/MUTE

button (1) on the front panel or

the

POWER

button (4) on the remote to power off the unit.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The
beep tone cannot be disabled.

Mute

Press the

/MUTE

button (1) on the front panel or remote (3)

to mute the volume from the unit. Press the

MUTE

button

again to restore the volume. The mute icon flashes on the
right side of the screen. Adjusting the volume or using any of
the audio set-up features cancels the mute function.

Playing Source Selection

Press the

SRC

button (11) on the remote to change between

available playing sources in the following order: TUNER,
DVD, AUX IN or CAMERA (rear view video camera). The
playing mode is displayed on the screen.

Press the

MENU/SRC

button (11) on the unit to access the

playing source menu. Use the direction buttons on the
joystick (6, 7, 8, 9) or remote control (14, 17, 18, 19, 22) to
select a playing source, then press the

button (18) or the

joystick enter button (5) to enter the selected source.

AUX IN Mode

An external peripheral device can be connected to this unit
via RCA output and “AUX-IN”.

CAMERA Mode

“CAMERA” mode is only available if the camera is connected
and during reverse driving. To install a rear view video
camera, connect the video input cable to the camera output
cable.

Volume Adjustment

To increase the volume level, press the

VOL +

button (3) on

the front panel or remote control. To decrease the volume
level, press the

VOL -

button (4) on the front panel or remote

control.The volume ranges from “0” to “40”. When the volume
level reaches “0” or “40”, a triple beep sounds, indicating that
the adjustment limit has been reached. The screen displays
the volume level for 3 seconds.

Programmable Turn-On Volume

This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.

To program a specific volume level, push and hold the

AUDIO

button (2) while the yellow volume bar is displayed on

the screen. The unit will beep two times to confirm your turn-
on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your
audio system to meet the acoustical characteristics of your
vehicle, which vary depending on the type of vehicle and its
measurements. To get the best possible sound quality from
your new system, be sure to adjust the settings for the
speakers as well. Proper setting of the Fader and Balance
boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the

AUDIO/LOC

button (2) on the front panel to display

the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Press the ( )/( ) buttons (8, 9) on the joystick or the (

(

) buttons (17, 19) on the remote control to select the audio

feature to be adjusted.

Adjusting an Audio Feature

Press the

buttons (14, 22) on the remote control or

the or buttons (6, 7) on the joystick to adjust the
selected feature to the desired setting.

NOTE: The Bass and Treble levels are only adjustable
when EQ is set to “User” mode.

The Loud function compensates for deficiencies in sound
ranges at low levels. Loudness levels range from 1-4 or “off”.
When the Loud function is on, LOUD is displayed on the
screen.

Exiting the Audio Control Menu

Press and hold the

AUDIO/LOC

button (2) or stop making

adjustments for a few seconds to exit the audio control menu.

Six-Channel Audio Control

NOTE: Before adjusting the volume of any speaker,
please refer to “Surround Setup” on page 18.

Rear Zone

If a monitor is installed in the rear zone and connected to the
rear zone AV output, passengers in the back seat can control
the DVD output using the rear zone remote control. See
“Multi-Zone Remote Control” on page 8 for instructions.

System Reset

To correct a system halt or other illegal
operation, use the tip of a pen to press
the

RESET

button (25) located on the

front bottom-left corner of the TFT screen. After a system
reset, the unit restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD
resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a
telephone call is received by the car phone or when verbal
navigation is performed. See “Wiring” on page 3.

Table 4: Audio Adjustments

Audio Function

Adjustable Range

User

Flat

Jazz

Pop

Classical

Rock

Vocal

Bass

-14 to +14