Jensen WMS190 Installation And Operation Manual Download

Page: 6 / 32

WMS190

BASIC OPERATION

Power On/Off

Press any button on the front panel to turn the unit on. Press the

POWER

button (1) to turn the

unit off. The

POWER

button is illuminated whenever the IGN lead (red wire) is powered,

regardless of whether the unit is on or off.

Volume Control

To increase the volume, press the

VOL +

button (2a). To decrease the volume, press the

VOL

button (2b).

Mute

Press the

MUTE

button (17) on the control panel to mute the audio output. Press

MUTE

again

to restore the audio output to the previous level.

Mode

Press the

MODE

button (4) on the control panel to select a different mode of operation, as

indicated on the display panel. Available modes include Tuner, SIRIUS and AUX In (optional
Auxiliary Input).

NOTE: SIRIUS mode will be skipped if the module is not installed.

Reset

The reset button (18) should be activated for the following reasons:

•

initial installation of the unit when all wiring is completed

•

function buttons do not operate

•

error symbol on the display

Use a ball point pin or thin metal object to press the

RESET

button (18). This may be

necessary should the unit display an error code.

You can recover factory default settings using the RESUME function located on the system
menu. With “YES” flashing, press the

MODE

button (4) to activate.

Audio Menu

Press the

AUDIO

button (3) on the control panel to access the audio menu. You can navigate

through the audio menu items by pressing the

AUDIO

button repeatedly. Once the desired

menu item appears on the display, adjust that option by pressing the

VOL

+/- buttons (2) within

5 seconds. The unit will automatically exit the audio menu after five seconds of inactivity. The
following menu items can be adjusted.

Bass Level

Use the

VOL

buttons to adjust the Bass level range from “-6” to “+6”.

Treble Level

Use the

VOL

buttons to adjust the Treble level range from “-6” to “+6”.

Balance

Use the

VOL

buttons to adjust the Balance between the left and right speakers from “L12” (full

left) to “R12” (full right).

Fader

Use the

VOL

buttons to adjust the Fader between the rear and front speakers from “R12” (full

rear) to “F12” (full front).

System Menu

Press and hold

the

AUDIO

button (3) for more than 3 seconds to enter the system menu.

“MENU” will appear on the display, followed by the first menu item, “CONTRAST.”

Press the

TUNE/TRK >>|

|<<

button (21, 20) or press the

AUDIO

button repeatedly to

navigate the system menu and select the desired item.

Press the

VOL

+/-

buttons (2) to adjust the selected menu item.

Press the

AS/PS

button to return to the previous operation immediately or wait for 5

seconds to return automatically.

The following items can be adjusted:

•

CONTRAST (0 – 10): Set LCD contrast.

•

LOW BATT (ON/OFF): Monitor voltage on ACC line.

•

DISTANT/LOCAL: Select LOCAL for tuner to access local stations whose signals are
much stronger. Select DISTANT to receive all broadcasts in your area.

•

AREA (USA/LATIN/EUROPE): Set frequency spacing for various regions.

•

VOL PGM (0 – 46): Select an automatic turn-on volume.

•

BEEP TONE (ON/OFF): Turn the audible beep ON/OFF (heard when functions/buttons
are selected).

NOTE: Beep tone off will not affect LOW BATT audible tone

•

RESUME: Return the EEPROM to factory default set up values and reset the Sirius Tuner
Settings. "Yes" will blink on the LCD to confirm. Press

MODE

to select.

LOW BATTERY Operation

If LOW BATT is set to “ON”, a alarm will sound (8 beeps every 30 sec) when the voltage drops
to 10.8V (+/- 0.03V). A visual warning (LOBA) will appear flashing (8 flashes every 30 sec) in
the lower left corner of the LCD display.

NOTE: “OFF” is the default setting for LOW BATT. If the audio is muted or the volume is
set to 0, the audible beep will not be heard.