background image

 

MAGPRO 35

 

10 of 10 

 

6.3 

Repairs 

Repairs may only be carried out by our 
customer service department! 

Repairs carried out by the operator can lead 
to accidents leading to death and serious 
damage to property for which the manufac-
turer is not liable! 

 

Warning 

6.4 

Troubleshooting 

Magnet is on, motor does not rotate despite switch operation 

Cause: Defective motor switch 

Solution: Replace switch 

 

Magnet is not on despite operation of magnet switch 

Cause: Rectifier defective 

Solution: Replace rectifier 

 

Unusual vibrations 

Cause: Shaft guide seat loose 

Solution: Tighten shaft guide seat 

Decommissioning and Disposal 

Ensure safe and environmentally-friendly 
disposal of the equipment. Any national 
rules and regulations must be observed!

 

Oil, grease and other liquids must be dis-
posed of separately in accordance with local 
regulations.

 

 

Replacement and Wear Parts 

Replacement parts must conform with our specified technical 
requirements. This is always the case with original replacement 
parts. Warranty is only maintained with our original replace-
ment parts. Installation and/or use of replacement parts not 
originally supplied by ourselves can possibly change design 
characteristics in a negative way and can have a negative 
effect on active or passive safety. All liability and warranty for 
damage which is caused by use of other than original replace-
ment parts or accessories is excluded on our side. 

Please order replacement parts from the customer service 
department. 

We require the following information in order to be able to 
process your replacement part order fast and easily: 

 

Customer 

 

Product identification data 

 

Name of desired replacement part 

 

Desired number of parts 

 

Desired mode of despatch 

 

 

 

Summary of Contents for MAGPRO TP 2000











Reviews: