JessEm Tool CLEAR CUT-TS Manual Download

Page: 1 / 10

CLEAR CUT - TS ™

61 Forest Plain Road

Oro-Medonte, Ontario, Canada

L3V 0R4

Toll Free: 1-800-436-6799

Local: 705-726-8233

Fax: 705-327-0295

Email: jessem@jessem.com

Website: www.jessem.com

Precision Stock Guides

for your Table Saw

Model #04301

Thank you for choosing this product from JessEm Tool

Company. We appreciate your support and hope that

our product serves you well. This product is designed to

provide many years of reliable service, provided it is

used as intended and taken care of.

This user manual will assist you in assembly and

general operation of this product. It is not our intent

to teach you about woodworking. It is assumed that

you are an experienced woodworker with the basic

skills and experience necessary to use this product

safely. If after reading the following instructions, if

you are unsure or uncomfortable about safely using

this product we urge you to seek additional

information through widely available woodworking

books or classes.

As part of our Continuous Product Improvement

Policy, JessEm Products are always advancing in

design and function. Therefore there may be

differences between what is shown in our catalogs,

website or at retail display and what is sold at time of

purchase. We reserve the right to make positive

changes to our products at our discretion.

IMPORTANT

Read and understand the contents of this

manual before assembly or operation of this

product.

IMPORTANT SAFETY PRECAUTIONS

Before operating any table saw, read and

understand all safety instructions in the

owners manual that came with the saw.

If you do not have a manual, contact the

manufacturer and obtain one before using

any power tool.

Always wear eye protection in compliance

with ANSI safety standards when

operating any power tool.

Always use proper guards and safety

devices when operating power tools and

machinery.

Carefully check saw blades before each use.

Do not use if damage or defect is suspected.

Do not wear loose clothing or jewelry that

may catch on tools or equipment.

Unplug the tool or machine when mounting

or making any adjustments to mechanical

performance

•

Summary of Contents for CLEAR CUT-TS











Search results

Summary of Contents for CLEAR CUT-TS

Reviews:

Related manuals for CLEAR CUT-TS

Brands by name

Popular brands

JessEm Tool CLEAR CUT-TS, Manual

Search results

Summary of Contents for CLEAR CUT-TS

Reviews:

Related manuals for CLEAR CUT-TS

Brands by name

Popular brands