JHI-A7-06-0001
Have questions? Call us at 562-467-0260 or email larrywjhi@jethangar.com
15
11.
Locate a 2-56x12” Dubro #108 push rod. Cut
to an overall length of approximately 5.25”.
Solder a clevis onto the unthreaded wire.
Thread the 2-56 clevis onto the threaded end.
Install the pushrod into the airplane.
Note:
Attach the solder clevis at the servo.
Adjust the 2-56 clevis to suit the centerpoint
of the servo.
6.2.2 Elevator
Again, different servo installations are required for the elevator installation on the
turbine and ducted fan versions. If desired, the ducted fan servo installation can
be used for the turbine installation, but NOT vice versa. The control horn setup
described below is common between the two kits. The elevator servo installation
for each is described in Sections 6.2.2.1 and 6.2.2.2.
12.
Locate the two elevators, 2 each ¼” wheel
collars, and two each 4-40x1” hex head bolts.
Using a Dremel cutoff wheel, bevel the head
of the 4-40 bolts. This will allow for the horn
brackets to reach to the top of the bolts.
Thread the horn brackets onto the 4-40 bolts.
Ensure they are screwed completely to the
top of the bolt head.
Drill and tap a 4-40 hole into the ¼” wheel
collar.
Test fit the elevators onto the fuselage.
Ensure smooth action of the elevators. If
necessary, the action can be smoothed out
by pressing a sharpened 9/32” brass tube
into the bushing on the elevator.
Note:
The
elevators angle upwards (dihedral) when
installed.
With the elevator in place, test fit the 1/4”
wheel collar onto the elevator torque rod.
Ensure the 4-40 bolt tightens into the 1/4”
wheel collar securely. With the assembly
tightened, check for any lateral movement of
the elevator; there should be none. If
necessary, add 1/64” spacers to the fuselage
to alleviate any lateral movement or rubbing
against fuselage.
Final install the elevators onto the fuselage.
Ensure the 4-40 bolt is completely tightened.
1/64” ply
spacers
Summary of Contents for A-7D/E Corsair II
