background image

10 

JAT-821A Pneumatic Flux Chipper

 

 

Replacement parts 

To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 
5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so 
that we may serve you quickly and accurately. 

Some parts are shown for reference only, and may not be available individually. 

 

#505822, JAT-821A, Flux Chipper – exploded view 

 

#505822, JAT-821A, Flux Chipper – parts list 

Index Part No. 

Description 

Qty 

1 730213-1 Back 

head 

3 730214A 

Throttle valve with O-Rings 

O-Ring 3.3x1.5 

O-Ring 3.55x1.8 

4 730215  Spring 

5 1008365  O-Ring 

D7.8x2.4-P8 

6 730216  Valve 

cap 

7 730217  Lever 

8  729538 

Spring pin 5x22L 

9 729747  Hose 

adaptor 

10 729597-1  Lock 

ring 

28 730218  Alignment 

shim 

29  729608 

Rear valve block 

 

Index Part No. 

Description 

Qty 

30

 

1012591

 

Pin

 

2

 

31

 

729604

 

Valve

 

1

 

32

 

729606

 

Front valve block

 

1

 

33 730219 

Piston 

35 731008 

Barrel 

sleeve 

36 731009 

Nose 

37 731010 

Key 

38 730220 

Driver 

retainer 

39 730221 

Retainer 

buffer 

40 JAT800-40-1  Barrel 

41 730222 

Retainer 

cap 

50 JAT821-50 

Chisel 

 JAT821A-RBK 

Rebuild 

Kit (#3,4,5,33,38) 

 

Summary of Contents for 505822













Reviews: