manualshive.com logo in svg

Jet DC-1200FS, Owner'S Manual

The Jet DC-1200FS is a powerful dust collector designed for efficient removal of dust and debris in your workshop. Ensure proper installation and operation with the comprehensive Owner's Manual, available for free download from our website. Get the most out of your product with this essential manual!

Share
Download
background image

6

WARNING

Read and understand the entire contents of

this manual before attempting assembly or

operation of the dust collector!

Failure to comply may cause serious injury!

Unpacking

1.

Remove all contents from the shipping
carton.

2.

Report any damage to your distributor.

3.

Do not discard any shipping material until
after the dust collector has been assembled
and is running properly.

Contents of the Shipping Carton

1.

Warranty Card

1.

Owner's Manual

1.

Motor/Fan Assembly

5.

Plastic Collector Bags

1.

Filter Bag

2.

Bag Clamps

2.

Supports

1.

Handle

4.

Casters & Hardware

1.

Bag Hanger

1.

Lower Stand

1.

Upper Stand

1.

Base

2.

Gaskets (o-ring type)

1.

Gasket (foam pad)

1.

Inlet

Tools Required for Assembly

6"-8" Adjustable Wrench or 14mm Wrench.
Cross Point or Flat Head Screwdriver.

Summary of Contents for DC-1200FS
















Reviews:

No comments

Related manuals for DC-1200FS

Fein 9-88-35 Brochure preview
9-88-35
Brand: Fein Pages: 12
Central Machinery 61808 Owner'S Manual & Safety Instructions preview
61808
Brand: Central Machinery Pages: 12

Brands by name

Popular brands

Load more brands