Jet HVBS-710G, Operating Instructions And Parts Manual

4 

3.0

  Safety Warnings 

1.  Read and understand the entire owner’s 

manual before attempting assembly or 
operation. 

2.  Read and understand the warnings posted on 

the machine and in this manual. Failure to 
comply with all of these warnings may cause 
serious injury. 

3.  Replace the warning labels if they become 

obscured or removed. 

4.  This band saw is designed and intended for 

use by properly trained and experienced 
personnel only. If you are not familiar with the 
proper and safe operation of a band saw, do 
not use until proper training and knowledge 
have been obtained. 

5.  Do not use this band saw for other than its 

intended use. If used for other purposes, JET 
disclaims any real or implied warranty and 
holds itself harmless from any injury that may 
result from that use. 

6. Always wear ANSI approved safety 

glasses/face shields while using this band 
saw. 

Everyday eyeglasses only have impact 

resistant lenses; they are not safety glasses.

7.  Before operating this machine, remove tie, 

rings, watches and other jewelry, and roll 
sleeves up past the elbows. Remove all loose 
clothing and confine long hair. Non-slip 
footwear or anti-skid floor strips are 
recommended. 

8.  Wear ear protectors (plugs or muffs) during 

extended periods of operation. 

9.  Do not operate this machine while tired or 

under the influence of drugs, alcohol or any 
medication. 

10.  Make certain the switch is in the 

OFF

 position 

before connecting the machine to the power 
supply. 

11. 

Make certain the machine is properly 
grounded. 

12.  Make all machine adjustments or maintenance 

with the machine unplugged from the power 
source. 

13.  Remove adjusting keys and wrenches. Form a 

habit of checking to see that keys and 
adjusting wrenches are removed from the 
machine before turning it on.  

14.  Keep safety guards in place at all times when 

the machine is in use. If removed for 
maintenance purposes, use extreme caution 

and replace the guards immediately after 
maintenance is complete. 

15. Make sure workpiece is securely clamped in 

the vise. Never use your hand to hold the 
workpiece. 

16. Check coolant level frequently. Replace dirty 

or weak coolant. 

17. Check damaged parts. Before further use of 

the machine, a guard or other part that is 
damaged should be carefully checked to 
determine that it will operate properly and 
perform its intended function. Check for 
alignment of moving parts, binding of moving 
parts, breakage of parts, mounting and any 
other conditions that may affect its operation. 
A guard or other part that is damaged should 
be properly repaired or replaced. 

18. Inspect blade for cracks, wear or missing 

teeth. Replace blade if these symptoms are 
found. 

19. Provide for adequate space surrounding work 

area and non-glare, overhead lighting. 

20. Keep the floor around the machine clean and 

free of scrap material, oil and grease. 

21. Keep visitors a safe distance from the work 

area. 

Keep children away.

22.  Make your workshop child proof with padlocks, 

master switches or by removing starter keys. 

23. Give your work undivided attention. Looking 

around, carrying on a conversation and “horse-
play” are careless acts that can result in 
serious injury. 

24.  Maintain a balanced stance at all times so that 

you do not fall or lean against the blade or 
other moving parts. Do not overreach or use 
excessive force to perform any machine 
operation. 

25. Use the right tool at the correct speed and 

feed rate. Do not force a tool or attachment to 
do a job for which it was not designed. The 
right tool will do the job better and more safely. 

26. Use recommended accessories; improper 

accessories may be hazardous. 

27. Maintain tools with care. Keep blades sharp 

and clean for the best and safest performance. 
Follow instructions for lubricating and changing 
accessories. 

28.  Make sure the workpiece is securely attached 

or clamped to the table. Never use your hand 
to hold the work piece. 

29. Turn off the machine and disconnect from 

power before cleaning. Use a brush to remove 
chips or swarf — do not use your hands. 

30. Do not stand on the machine. Serious injury 

could occur if the machine tips over.