background image

 

4

 

 

Warning 

1.  Read and understand the entire owner’s manual before using the pallet truck. 

2.  Do not place hands or feet under the pallet truck at any time. 

3.  Never allow anyone to ride on the pallet truck. 

4.  Operate on smooth, level, finished floors only; do not use on ramps or sloping floors. 

5.  To prevent accidental tipping, make sure load is centered on the fork. 

6.  Do not lift a load with fork tips only. This may cause damage to the fork and personal injury if the rear 

of the pallet truck suddenly tips upward. 

7.  Do not load pallet truck beyond its rated capacity. 

8.  Never leave a loaded pallet truck unattended in the raised position. Always lower load to the floor. 

9.  Pull pump release lever slowly to allow load to descend in a controlled manner. 

10.  Secure load before transporting. 

11.  Do not move a loaded pallet truck by other than manual force. 

12. The handle is designed to pull and steer the pallet truck only. Do not use the handle as a leverage 

tool. 

13.  Failure to comply with these warnings may result in personal injury and/or property damage. 

14. 

 

WARNING:

 This product can expose you to chemicals including lead and cadmium which are 

known to the State of California to cause cancer and birth defects or other reproductive harm, and 
phthalates which are known to the State of California to cause birth defects or other reproductive 
harm. For more information go to http://www.p65warnings.ca.gov. 

 

Introduction 

This manual is provided by JET covering the safe operation and maintenance procedures for a JET 
Model JTX or PTX Heavy Duty Pallet Truck. This manual contains instructions on assembly, safety 
precautions, general operating procedures, maintenance instructions and parts breakdown. This product 
has been designed and constructed to provide consistent, long-term operation if used in accordance with 
instructions set forth in this manual. If there are any questions or comments, please contact either your 
local supplier or JET. JET can also be reached at our web site: www.jettools.com. 

Retain this manual for future reference. If the pallet truck transfers ownership, the manual should 
accompany it. 

 

  Read and understand the entire contents of this manual before attempting 

assembly or operation!  Failure to comply may cause serious injury! 

 

Register your product using the mail-in card provided, or register online: 

http://www.jettools.com/us/en/service-and-support/warranty/registration/ 

 

 

 

Summary of Contents for JTX-2748

















Reviews: