Jet JWL-1640EVS, Operating Instructions And Parts Manual

5 

4.0

  Specifications  

 
Model number .......................................................................................................................................... JWL-1640EVS 
Stock number ....................................................................................................................................................... 719500 
 
Motor and electricals: 
 

Motor type ........................................................................................................ totally enclosed fan cooled, induction 

Horsepower ....................................................................................................................................... 1.5HP (1.1 kW) 

Phase ....................................................................................................................................................................... 3 

Voltage ............................................................................................................................................................. 230 V 

Cycle .................................................................................................................................................................. 60Hz 

Listed FLA (full load amps) ................................................................................................................................ 4.6 A 

Starting amps ..................................................................................................................................................... 5.8 A 

Running amps (no load) ....................................................................................................................................... 3 A 

Power transfer .................................................................................................................................................. V-belt 

Drive .......................................................................................................... electronic variable speed, inverter control 

On/off switch ............................................................................................... paddle switch with removable safety key 

Motor speed ............................................................................................................................................... 1720 RPM 

Power cord.............................................................................................................................. SJT 3x14AWG (300V) 

Power cord length ................................................................................................................................... 6 ft. (183cm) 

Power plug installed ..................................................................................................................................... 5-15P UL 

Power input requirements ...................................................................................................

single phase, 115V only

Recommended circuit size

1

 ................................................................................................................................ 15 A 

Noise emission without load 

2

 ..................................................................................... 

78 dB at 20 inches from motor

 
Capacities: 
 

Working distance between centers .......................................................... 39 in. (990 mm) with single bearing center 

Working distance between centers .................................................................. 37 in. (940 mm) with live cone center 

Working distance between centers, optional 20” bed ext. mounted ............... 59 in. (1543 mm) single bearing center 

Working distance between centers, optional 20” bed ext. mounted ............... 57 in. (1447 mm) with live cone center 

Maximum distance between spindle face and tailstock quill, optional 20” bed ext. mounted ..... 60-1/2 in. (1536 mm) 

Swing over bed ............................................................................................................................... 16.5 in. (419 mm) 

Swing over tool rest base ............................................................................................................ 12-7/8 in. (327 mm) 

Indexing .................................................................................... 36 positions, positive locking, 10 degree increments 

Swing over 20” bed extension in low position

 (optional accessory)

 ............................................. 34-1/2 in. (876 mm) 

  
Headstock and Spindle: 
 

Spindle taper ...................................................................................................................................................... MT-2 

Spindle thread, inboard ...................................................................................................................... 1-1/4 in. x 8 TPI 

Spindle thread, outboard ........................................................................................................................ 3/4"-16 (LH) 

Spindle speed (RPM) ................................................................... variable within 40-1200 (low) and 100-3200 (high) 

Headstock spindle bore ...................................................................................................................... 3/8 in. (10 mm) 

Spindle direction ......................................................................................................................... forward and reverse 

Headstock movement ....................................................................................................................................... sliding 

 
Tailstock: 
 

Tailstock quill taper ............................................................................................................................................ MT-2 

Tailstock bore ..................................................................................................................................... 5/16 in. (9 mm) 

Tailstock quill travel ....................................................................................................................... 4-1/4 in. (108 mm) 

Tailstock quill thread .................................................................................................................... acme, 

3/4”-10

 (LH) 

 
Materials: 
 

Legs .............................................................................................................................................................. cast iron 

Bed ............................................................................................................................................................... cast iron 

Headstock ..................................................................................................................................................... cast iron 

Headstock spindle .............................................................................................................................................. steel 

Tailstock ....................................................................................................................................................... cast iron 

Tailstock quill ................................................................................... hardened HRC20 steel, with laser etched scale 

Tool support and base .................................................................................................................................. cast iron 

1

 subject to local/national electrical codes 

2 

The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace 

conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks 
involved only.