background image

 

30 

14.3.2

  JWL-1840EVS Bed and Stand Assembly – Parts List 

Index No.  Part No. 

Description 

Size 

Qty

 

1 ................ JET-113 ..................... JET Nameplate ........................................................ 113x47mm .................... 1 

2 ................ JWL1440-202 ............ Bed ..........................................................................  ...................................... 1 

3 ................ JWL1440-203 ............ Stud .........................................................................  ...................................... 2 

4 ................ 6294742E .................. Tool Rest ................................................................. 14" ................................. 1 

 .................. JWL1440-TREA ........ Optional Tool Rest Extension Assembly (includes #5, 7, 33, 36) ......  ............ 1 

5 ................ JWL1440-205 ............ Tool Rest Extension, Optional .................................  ...................................... 1 

 .................. JWL1840EVS-TBA .... Tool Rest Base Assembly (includes #6 thru 13, 33, 34, 35)  .......................... 1 

6 ................ JWL1440-206 ............ Handle ..................................................................... 3/8" ................................ 1 

7 ................ JWL1440-207 ............ Tool Rest Lock Bushing Set ....................................  ...................................... 2 

8 ................ JWL1840EVS-308 ..... Tool Rest Base ........................................................  ...................................... 1 

9 ................ JWL1840EVS-309 ..... Tool Support Rod ....................................................  ...................................... 1 

10 .............. JWL1442-128 ............ Clamp Bolt ...............................................................  ...................................... 1 

11 .............. JWL1442-154 ............ Clamp ......................................................................  ...................................... 1 

12 .............. TS-0650081 .............. Hex Nylon Lock Nut ................................................. 3/4”-10 .......................... 1 

13 .............. JWL1840EVS-313 ..... C-Ring ..................................................................... S-18 .............................. 1 

14 .............. 708331 ...................... Live Center Assembly (includes #15 thru 18) ..........  ...................................... 1 

15 .............. JML-52A .................... Center Point for Live Center ....................................  ...................................... 1 

16 .............. JML-52 ...................... Live Center Head .....................................................  ...................................... 1 

17 .............. BB-6002ZZ ................ Ball Bearing ............................................................. 6002ZZ ......................... 1 

18 .............. JML-54 ...................... Live Center Shaft .....................................................  ...................................... 1 

 .................. JWL1840EVS-TA ...... Tailstock Assembly (includes #19 thru 30, 38, 39) ..  ...................................... 1 

19 .............. JWL1640EVS-319 ..... Quill ......................................................................... MT2 ............................... 1 

20 .............. JWL1640EVS-320 ..... Lead Screw ..............................................................  ...................................... 1 

21 .............. JWL1440-221 ............ Tailstock Rod ...........................................................  ...................................... 1 

22 .............. JWL1221VS-227 ....... Key ..........................................................................  ...................................... 1 

23 .............. JWL1640EVS-323 ..... Socket Head Button Screw ...................................... #10-32x5/8” ................... 1 

24 .............. JWL1015-137 ............ Tailstock Lock Handle .............................................  ...................................... 1 

25 .............. JWL1840EVS-325 ..... Tailstock Casting .....................................................  ...................................... 1 

26 .............. JWL1440-226 ............ Handwheel ...............................................................  ...................................... 1 

27 .............. JWL1442-211 ............ Handle .....................................................................  ...................................... 1 

28 .............. TS-0267041 .............. Set Screw ................................................................ 1/4"-20x 3/8” ................. 2 

29 .............. JWL1440-229 ............ C-Ring ..................................................................... S-12 .............................. 1 

30 .............. JWL1440-230 ............ Bolt ..........................................................................  ...................................... 1 

31 .............. LM000214 ................. ID Label, JWL-1840EVS ..........................................  ...................................... 1 

32 .............. JWL1221VS-211 ....... Warning Label .........................................................  ...................................... 1 

33 .............. TS-0570031 .............. Hex Nut .................................................................... 3/8” ................................ 2 

34 .............. TS-0267021 .............. Set Screw ................................................................ 1/4”-20x1/4” .................. 2 

35 .............. JWL1442-228 ............ C-Ring ..................................................................... S-25 .............................. 1 

36 .............. JWL1440-206 ............ Handle, Optional ......................................................  ...................................... 1 

38 .............. JWL1442-154 ............ Clamp ......................................................................  ...................................... 1 

39 .............. TS-0650081 .............. Hex Nylon Lock Nut ................................................. 3/4”-10 .......................... 1 

 .................. 6295902 .................... Live Center Assembly (includes index #40 thru #43) ..................................... 1 

40 .............. 6295905 .................... Live Center Cone .....................................................  ...................................... 1 

41 .............. 6295904 .................... Live Center Tip ........................................................  ...................................... 1 

42 .............. 6295903 .................... Live Center Body .....................................................  ...................................... 1 

43 .............. 6295906 .................... Live Center Rod .......................................................  ...................................... 1 

47 .............. TS-0209031 .............. Socket Head Cap Screw ......................................... 3/8"-16x3/4” .................. 2 

48 .............. TS-0680042 .............. Flat Washer ............................................................. 3/8" ................................ 5 

49 .............. JWL1640EVS-349 ..... Tool Shelf ................................................................  ...................................... 1 

50 .............. JWL1840EVS-350 ..... Leg ...........................................................................  ...................................... 2 

51 .............. TS-0208071 .............. Socket Head Cap Screw ......................................... 5/16"-18x1-1/4" ............. 8 

52 .............. TS-0720081 .............. Lock Washer ............................................................ 5/16" .............................. 8 

53 .............. TS-0680031 .............. Flat Washer ............................................................. 5/16" .............................. 8 

54 .............. JWL1642-206 ............ Adjustable Foot ........................................................ 3/8" ................................ 4 

55 .............. TS-0561031 .............. Hex Nut .................................................................... 3/8" ................................ 4 

56 .............. JWL1840EVS-356 ..... Riser Block ..............................................................  ...................................... 2 

57 .............. TS-0060061 .............. Hex Cap Screw ........................................................ 3/8"-16x1-1/4" ............... 4 

58 .............. TS-0720091 .............. Lock Washer ............................................................ 3/8" ................................ 4 

59 .............. TS-0680041 .............. Flat Washer ............................................................. 3/8" ................................ 4 

Summary of Contents for JWL1440-TREA






































Reviews: