background image

This function is of use in case of a bidirectional connection of several 

receivers or satellite receivers. The output channel 

marked Sat 1 can be set to PPM signal mode only. 

-Set mode SAT: on the Duplex receivers R9,R10, R11EPC, R12EPC, 

R14, R18 the outputs SAT1 and SAT2 can be 

affiliated with following functions 

- PPM Off: the particular output is neither generating nor receiving a 

PPM signal 

- PPM Input: the particular input is expecting a PPM signal of the 

connected receiver 

- PPM Output: the receiver will generate PPM signals on output SAT2 

-Set mode SAT: on the Duplex receivers R11, R12, R18 the outputs 

SAT1 and SAT2 can be affiliated with following 

functions 

- CH xx: the PPM signal on the particular output will neither be 

generated nor received. The output has the same 

function like the outputs Y1-Y16. 

- PPM Input: the particular input is expecting a PPM signal of the 

connected receiver 

- PPM Output: the receiver will generate PPM signals on the output 

SAT2 

Receivers EN 

- PPM Alarm Code: if one of the outputs SAT1/2 is set to PPM input 

mode, an acoustic signal can be set up which 

reports absence of the connected signal. By means of loading a 

morsealphabet character tones are set, which 

acoustically announce the absence of the PPM signal at the particular 

receiver input. These acoustic signals are 

generated by the transmitter module. 

function -Set Input Channel: affiliation to particular outputs, any input 

channel or its mixing product which 

may be specified in the menu Channel Set can be set up. 

-Reverse A: makes throw reverse at the output in the half plane A 

possible, the half planes are subdivided 

according to the neutral position setup (Channel set - Set Center) 

-Reverse B: makes throw reverse at the output in the half plane B 

possible 

-Gain A: Amplification of the output throw in half plane A (100% - 

without changes) 

-Gain B: Amplification of the output throw in half plane B (100% - 

without changes) 

-Signal Fault: setup of the receiver behaviour in case of signal loss, 

repeat- repetition of the last valid throw 

Summary of Contents for Jeti Duplex EX R11












Reviews: