SECTION 2 - SERVICE PROCEDURES
31215808
2-27
25. Carefully slide mast section-3 into section-2 until ends
are even. Check to make sure chain assembly
(wide
chains)
are seating properly in chain anchor block chain
sheave wheels attached to mast section-2.
26. Insert slide pads into the top end mast rails between sec-
tion-2 and -3,
(one on each side of the mast)
, with beveled
surface facing inward towards section-3.
NOTE:
Before fastening and shimming the slide pad on the top
left side of the mast, install a sequence cable bracket
against the mast under the flatwasher.
27. Thread slide pad attaching bolts, two (2) 1/4 in. x 7/8 in.
long hex head bolts, place a flat washer under head of
each bolt, through holes in outside rail, on top of mast
section-2 and into the slide pad inserts. Thread in
enough to hold pad in place.
28. Shim per instructions in step 7, Mast Section 2 - Assem-
bly.
29. Insert slide pads into the bottom end mast rails between
section-2 and -3,
(one on each side of the mast)
, with bev-
eled surface facing out towards section-2.
30. Thread slide pad attaching bolts, two (2) 1/4 in. x 3/4 in.
long hex head bolts, place a flat washer under head of
each bolt, through holes on inside rail, on bottom end of
mast section-3 and into the slide pad inserts. Thread in
enough to hold pad in place.
31. Shim per instructions in step 7, Mast Section 2 - Assem-
bly.
Mast Section 4 - Assembly
(All Masts)
NOTE:
When sliding mast sections together, be careful not to
scratch or score the anodized finish in the slide pad chan-
nels.
32. Locate mast section-4, carefully slide section-4 closed rail
into section-3 open rail. Slide sections together until
ends are even.
33. Locate one (1) of the attach bracket (one with threaded
holes horizontally aligned to outside of bracket). Attach
using outer set of holes in bottom of mast section-3 with
three (3) 1/4 in. x 3/4 in. long bolts, place a flatwasher
under head of each bolt.
34. Slide mast section-4 out the top of mast section-3 so the
bracket on bottom of mast section-4 is easily accessible
at top end of mast section-3. Rest the top end of mast
section-4 on a support while performing next step.
35. Insert threaded ends of chain assembly
(attached to
anchor block on top mast section-2)
through the bracket
located on bottom of extended mast section-4. Loosely
thread two (2) 3/8 in. nuts onto stud threads on each
chain. Chains will be adjusted later in assembly.
36. Insert chain adjustment into the top of mast section-4 by
using spacer, chain equalizer and Keeper. Secure one end
of the chain assembly with chain adjustment by using
two (2) pin, cotter pin and washer.
37. While mast section-4 is still extended from section-3,
assemble cable sheaves to top of mast section-4 as fol-
lows;
a. Locate the wide tube spacer and slide onto sheave
pin.
b. Slide two (2) cable sheave wheels onto sheave pin,
one each end of sheave pin to outside of tube
spacer.
c. Place two (2) thrust washers, one each end of
sheave pin to outside of cable sheave wheels.
d. Place two (2) sheave pin attach bars, one each end
of sheave pin to outside of large flatwashers.
e. Holding complete cable sheave wheel assembly,
slide assembly into top of mast section-4 and align
threaded holes in sheave pin attach bars with holes
in mast rails.
f.
Attach to top of mast section-4 using two (2) 3/8 in.
x 1/2 in. long socket head-countersunk-flathead cap
screws, each side. Apply Medium Strength Thread-
locking Compound and tighten.
NOTE:
When sliding mast sections together, be careful not to
scratch or score the anodized finish in the slide pad chan-
nels.
38. Carefully slide mast section-4 back into section-3 until
ends are even. Check to make sure chain assembly
(nar-
row chains)
are seating properly in chain sheave wheels
attached to top of mast section-3.
39. Insert slide pads into the top end mast rails between sec-
tion-3 and -4,
(one on each side of the mast)
, with beveled
surface facing inward towards section-4.
NOTE:
Before fastening and shimming the slide pad on the top
left side of the mast, install a sequence cable bracket
against the mast under the flatwasher.
40. Thread slide pad attaching bolts, (two (2) 1/4 in.
x 7/8 in.
long hex head bolts, place a flat washer under head of
each bolt), through holes in outside rail, on top of mast
section-3 and into the slide pad inserts. Thread in
enough to hold pad in place.
41. Shim per instructions in step 7, Mast Section 2 - Assem-
bly.
42. Insert slide pads into the bottom end mast rails between
section-3 and -4, (one on each side of the mast), with
beveled surface facing out towards section-3.
43. Thread slide pad attaching bolts, (two (2) 1/4 in. x 3/4 in.
long hex head bolts, place a flat washer under head of
each bolt), through holes on inside rail, on bottom end of
mast section-4 and into the slide pad inserts. Thread in
enough to hold pad in place.
44. Shim per instructions in step 7, Mast Section 2 - Assem-
bly.
Go
to
Discount-Equipment.com
to
order
your
parts
