SECTION 5 - JLG CONTROL SYSTEM
3121788
5-9
Fi
gur
e
5-
5.
Analyz
er M
enu - P
ersonalities
an
d Machine S
etup (
Version
P1.10) -
Sh
eet
3 of 3
1001206398-M
MENU:
MACHINE SETUP
1
MODEL:
UNKNOWN
NO MODEL
1932R
4045R
1532R
1
MARKET:
ANSI
ANSI EXPORT
CSA
CE
AUSTRALIA
JAPAN
GB
KOREA
1
DRIVE CUTOUT:
YES
NO
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CHARGER INTRLCK:
DRIVE ONLY
DRIVE AND LIFT
GROUND ALARM:
MOTION
HORN ONLY
DESCENT
LOAD:
NO
CUTOUT PLTM
CUTOUT ALL
BATTERY:
FLOODED
AGM
BEACON:
NO
LOW TEMP CUTOUT:
YES
NO
WHITE NOISE
ALARM:
YES NO
PHP ALARM:
YES NO
OVRHEAD PROTECT:
YES NO
MENU:
CALIBRATIONS
CALIBRATIONS:
TILT SENSOR
CALIBRATE TILT
SENSOR?
LEVEL VEHICLE:
YES:ENTER, NO:ESC
LEVEL VEHICLE:
TILT +X.X, +Y.Y
LEVEL VEHICLE:
SENSOR FAILURE
LEVEL VEHICLE:
NOT LEVEL
RAW TILT:
TILT +X.X, +Y.Y
CALIBRATIONS:
SET STOW ELEV
CALIBRATE STOW:
ELEV SENSOR?
SET STOW ELEV:
YES: ENTER, NO:ESC
SET STOW ELEV:
COMPLETE!
SET STOW ELEV:
SENSOR FAILURE
SET STOW ELEV:
X.XXV
CALIBRATIONS:
SET MAX ELEV
CALIBRATE MAX:
ELEV SENSOR?
SET MAX ELEV:
YES: ENTER, NO:ESC
SET MAX ELEV:
YES: ENTER, NO:ESC
SET MAX ELEV:
COMPLETE!
SET MAX ELEV:
SENSOR FAILURE
SET MAX ELEV:
X.XXV
CALIBRATIONS:
JOYSTICK
CAL JOYSTICK:
YES:ENTER, NO:ESC
CAL JOYSTICK:
FWD TO MAX
CAL JOYSTICK:
CENTER
CAL JOYSTICK:
REV TO MAX
CAL JOYSTICK:
COMPLETE!
CAL JOYSTICK:
CAL FAIL!
CALIBRATIONS:
LOAD 0%
CAL LOAD:
YES:ENTER, NO:ESC
CAL LOAD: FAIL
NOT IN GND MODE
CAL LOAD: FAIL
CAL ANGLE
CAL LOAD: FAIL
PLATFORM EMPTY?
CAL LOAD:
PLAT NOT STOWED
CAL LOAD: FAIL
LIFT TO MAX ELEV
CAL LOAD:
LOWER TO STOWED
CAL LOAD:
LIFT TO MAX ELEV
CAL LOAD:
LOWER TO STOWED
CAL LOAD:
MOTION STOPPED
CAL LOAD: FAIL
COMPLETE!
CAL LOAD:
CAL FAIL
CAL LOAD:
CALIBRATIONS:
LOAD 110%
CAL LOAD:
YES:ENTER, NO:ESC
CAL0% NOT DONE
CAL LOAD: FAIL
NOT IN GND MODE
CAL LOAD: FAIL
CAL ANGLE
CAL LOAD: FAIL
110% RATED LOAD?
CAL LOAD:
PLAT NOT STOWED
CAL LOAD: FAIL
LIFT TO MAX ELEV
CAL LOAD:
LOWER TO STOWED
CAL LOAD:
LIFT TO MAX ELEV
CAL LOAD:
LOWER TO STOWED
CAL LOAD:
MOTION STOPPED
CAL LOAD: FAIL
COMPLETE!
CAL LOAD:
CAL FAIL
CAL LOAD:
CALIBRATIONS:
VERIFY LOAD
VERIFY LOAD:
YES:ENTER, NO:ESC
CAL0% NOT DONE
VFY LOAD: FAIL
NOT IN GND MODE
VFY LOAD: FAIL
CAL ANGLE
VFY LOAD: FAIL
PLTFORM EMPTY?
VFY LOAD:
PLAT NOT STOWED
VFY LOAD: FAIL
LIFT TO MAX ELEV
VFY LOAD:
LOWER TO STOWED
VFY LOAD:
MOTION STOPPED
VFY LOAD: FAIL
COMPLETE!
VERIFY LOAD:
CAL FAIL
VERIFY LOAD:
CALIBRATIONS:
DRIVE CUTOUT
CALIBRATE DRIVE:
CUTOUT?
DRIVE CUTOUT:
YES:ENTER, NO:ESC
DRIVE CUTOUT:
COMPLETE!
DRIVE CUTOUT:
SENSOR FAILURE
DRIVE CUTOUT:
XXX.X IN
CALIBRATIONS:
SET ARM GAURD
CALIBRATE
ARMGAURD?
LIFT PLTFORM TO
ARMGAURD HEIGHT
SET ARM GAURD:
COMPLETE!
SET ARM GAURD:
SENSOR FAILURE
SET ARM GAURD:
XXX.X IN
CALIBRATIONS:
RESET PUMP MOD
RESET PUMP MOD
PARAMETERS?
WRITING
PARAMETERS
RESET PUMP MOD
COMPLETE!
RESET PUMP MOD
FAILED!
CALIBRATIONS:
RELIEF PRESSURE
LIFT UP TO RUN
PUMP
RELEASE LIFT UP!
NOT IN GROUND MODE!
SERVICE MODE
MENU:
LIFT OVERRIDE?
SERVICE MODE:
ACTIVE
LIFT OVERRIDE:
MAF10050M
3246R
Go to
Discount-Equipment.com
to
order your
parts
