SECTION
4
- BOO
M
& PLATFOR
M
3121160
4-15
6.
Remove hardware securing the boom pivot pin to the
upright. Using a suitable brass drift and hammer,
remove the pivot pin from upright.
7.
Using all applicable safety precautions, carefully lift
boom assembly clear of upright and lower to ground or
suitably supported work surface.
NOTE:
The main boom alone weighs approximately 2226 lbs.
(1010 kg). Including the slave cylinder, rotator, and plat-
form support the assembly weighs approximately 3185 lbs.
(1445 kg).
Disassembly
1.
Remove hardware securing telescope cylinder to after
end of the base boom section.
2.
Remove hardware which secures the wear pads to the
base boom section; remove the wear pads from the top,
sides and bottom of the base boom section.
3.
Using overhead crane or suitable lifting device, remove
fly boom assembly from base section.
4.
Remove hardware from the telescope cylinder pin.
Using a suitable brass drift and hammer remove the cyl-
inder pin from fly boom section.
5.
Pull the telescope cylinder partially from after end of the
fly boom section; secure the cylinder with a suitable
sling and lifting device at approximately the center of
gravity.
6.
Carefully remove the telescope cylinder and place tele-
scope cylinder on a suitable trestle.
NOTE:
The Main Boom Telescope Cylinder can be removed with-
out the main boom disassembly by disconnecting hydrau-
lic lines, top attaching pin of main lift cylinder and
telescope cylinders as directed above, and pulling out the
telescope cylinder from the rear, thru the access plate
opening of the upright.
7.
Remove hardware which secures the wear pads to the
after end of fly boom section; remove the wear pads
from the top, sides and bottom of the fly boom section.
Summary of Contents for 740AJ
