Checkout and maintenance
1-4
F/p CODE DEsCRIpTIONs OF THE BALANCER
F/P 1 TOGGLE FINE WEIGHT MODE
When
F/p 1
is activated, the machine displays
“FIN” “ON”
for one second (round off 0.05 oz or 1 gram).
Toggle
F/p
1 again changes back to the normal round off and display changes to
“FIN” “OFF”
for one sec-
ond (round off 0.25 oz or 5 gram).
F/P 2 RIM WIDTH INCH / MILLIMETER
Selecting
F/p 2
toggles the balancer between inch and millimeters for rim width. unit will display
“DtH I
NCH”
for inches pressing
F/p 2
again toggles to millimeters and the display changes to
“DtH”
for millimeters.
F/P 3 GRAM / OUNCE
Selecting
F/p 3
toggles the balancer between Grams and Ounces. unit will display
“OU” “NCE”
for ounce
pressing
F/p
3
again toggles to Grams and the display changes to
“gR” “gR” “gR”
.
F/P 4 CALIBRATION WITH ADAPTER OR DISABLE ADAPTER COMPENSATION
Some special tires and those wheels whose center holes are not the primary reference but are lug-centric re
-
quire an adapter. Lug-centric identifies that the tire and wheel assembly to be centered on it’s axis of rotation
must be mounted using the lug pattern instead of the center hole of the wheel. In this case, the adapter may
introduce an unbalance to the spin system. This means that this unbalance has to be compensated for after
tire unbalance is measured. This
F/p
code is used to measure the unbalance of shaft and adapter together
and saves it in memory and set an adapter compensation flag to tell the program to use adapter compensa
-
tion after tire balance is done.
F/p
4 is a toggle, it is used to turn this flag off.
• After
F/p
4 is activated, machine displays
“CAL ADp”
for one second. And then it displays
“spN”
“1”
.
Operator spins the shaft just like ordinary balancing. When the machine is taking data and calculation,
it displays “CAL BAL” to tell the operator the machine is working on the balancing procedure. Once the
calibration is done, machine displays
“ADp” “FIN”
to indicate the calibration is successful. Once the
shaft stops, machine displays
“---” “ ---”
and exits the
F/p4
automatically. The machine is now in an
idle state.
• When the machine is working under the application of an adapter, the balancing mode display is differ
-
ent than ordinary balancing. In ordinary balancing the machine displays
“---” “2pL”
while the machine
is taking data. In balancing with an adapter, the machine displays
“Adp” “2pL”
as it takes data. This
reminds the operator he is under adapter compensation mode. So if the operator does not use an
adapter and the machine displays
“Adp”
in left the window, the operator should turn off the adapter
compensation by toggling
<F> <4>
, or by cycling power.
F/P 7 TOGGLE MILLIMETER AND INCH FOR DIAMETER
If a metric tire is to be balanced, the diameter can be changed to enter the tire parameters in millimeters in
-
stead of inches. The default is set to inches. Pressing <
F/p
7> again toggles the balancer and forth between
inches and millimeters.
“DIA” “--I” “NCH”
= inches,
“DIA” “---” “---”
= millimeters.
F/P 12 READ COUNTERS
The balancer has 4 counters that keeps track of total number of cycles for a certain parameter. The balancer
will automatically cycle through the counters after
<F/p12>
is activated. The order of the counters.
Display
1.
“Ctr” “ALL”
for one second.
Total number of spins.
Display
2.
“Ctr” “CAL”
for one second.
Total number of spins since last calibration.
Display
3.
“Ctr” “srV”
for one second.
Total number of service spins.
Display
4.
“Ctr” “UsR”
for one second.
Total number of user spins.
The display will cycle through continuously through each step until
5.
“sTOp”
is pressed.
Summary of Contents for EEWB304B
Page 1: ...WHEEL BALANCER Service Manual EEWB502B C EEWB503B EEWB304B ...
Page 56: ......
