background image

070.250-IOM (APR 11)

Page 16

408 MM ROTARY SCREW COMPRESSOR

OPERATION

OPERATION

OPERATION AND START-UP INSTRUCTIONS 

The  Frick  408  mm  Rotary  Screw  Compressor  will  be  a 
component in an integrated system. As such the compressor 
requires some specific operation and conditions to ensure 
trouble-free running.

The information in this section of the manual provides the 
logical  step-by-step  instructions  to  properly  start  up  and 
operate the 408 mm Rotary Screw Compressor in your unit.  
Only matters which may influence the proper operation of 
the 408 mm compressor are included.

THE  FOLLOWING  SUBSECTIONS  MUST  BE  READ  AND 
UNDERSTOOD  BEFORE  ATTEMPTING  TO  START  OR 
OPERATE THE UNIT. 

COMPRESSOR HYDRAULIC SYSTEM 

(The solenoid valves and manifold block are 

available as a sales order option)

The compressor hydraulic system actuates the movable slide 
valve (SV) to load and unload the compressor. It also actuates 
the  movable  slide  stop  (SS)  to  increase  or  decrease  the 
compressor’s  volume  ratio  (Vi).  The  hydraulic  cylinder 
located at the inlet end of the 408 mm compressor serves a 
dual  purpose.  It  is  separated  by  a  fixed  bulkhead  into  two 
sections. The SV section is to the left of the bulkhead and 
the SS is to the right if you are facing the right side of the 
compressor.  Both  operations  are  controlled  by  solenoid 
valves, which are actuated when a signal from the appropriate 
microprocessor output energizes the solenoid valve. 

SINGLE-ACTING MODE - High Stage 
Open valve at SC1 
Close valve at SC2 
Open valve at BP (bypass) 

High  stage  compressor  loading:

  The  compressor  loads 

when SV solenoid YY2 is energized and oil flows from the 
unload side of the cylinder out port SC1, through valve ports 
A and T to compressor suction. Simultaneously, discharge 
pressure loads the slide valve. 

High  stage  compressor  unloading:

  The  compressor 

unloads when SV solenoid YY1 is energized and oil flows 
from the oil manifold through valve ports P and A to cylinder 
port  SC1  and  enters  the  unload  side  of  the  cylinder. 
Simultaneously,  gas  on  the  load  side  of  the  cylinder  is 
vented  through  port  SC2  and  valve  BP  to  compressor 
suction.

NOTICE

To control the rate of loading and unloading, throttle 
the needle valve at SC1 port.

 

DOUBLE-ACTING MODE - Booster (low differential)
Open valve at SC1 
Open valve at SC2 
Close valve at BP (bypass) 

Booster Compressor Loading:

 The compressor loads when 

SV  solenoid  YY2  is  energized  and  oil  flows  from  the  oil 
manifold through valve ports P and B to cylinder port SC2 
and enters the load side of the cylinder. Simultaneously, oil 
contained  in  the  unload  side  of  the  cylinder  flows  out 
cylinder port SC1 through valve ports A and T to compressor 
suction. 

Booster Compressor Unloading:

 The compressor unloads 

when SV solenoid YY1 is energized and oil flows from the 
oil  manifold  through  valve  ports  P  and  A  to  cylinder  port 
SC1 and enters the unload side of the cylinder. Simultaneously, 
oil contained in the load side of the cylinder flows out of 
compressor  port  SC2  through  valve  ports  B  and  T  to 
compressor suction.

NOTICE

To control the rate of loading and unloading, throttle 
valves SC1 and SC2.

NOTICE

To slow all valve movements - loading, unloading, and 
Vi change - throttle valve 2.

Figure 10 - Solenoid Valve Block

 

CAUTION

NEVER open valve BP and valve SC2 at the same time 

during compressor operation.

VOLUMIZER VOLUME RATIO CONTROL

 

Open valve at SC3 
Open valve at SC4 

Compressor Vi increase:

 The volume ratio Vi is increased 

when  MSS  solenoid  valve  YY3  is  energized  and  oil  flows 
from  the  oil  manifold  through  valve  ports  P  and  A  to 
compressor  port  SC3,  enters  the  increase  side  of  the 
cylinder and overcomes the decrease spring tension. 

Compressor Vi decrease:

 The volume ratio Vi is decreased 

when  MSS  solenoid  valve  YY4  is  energized  and  oil  flows 
from SC3 through valve ports A and T to compressor port 
SC4, to compressor suction. 

TO  CONTROL  THE  RATE  OF  Vi  CHANGE,  THROTTLE  THE 
NEEDLE VALVE AT SC3 PORT.

Summary of Contents for Frick 408L





























Reviews: