background image

Table 3: Accessories Ordering Information

Code number

Description

FX-WRZSST-120

Wireless Sensing System Tool: For Use with an FX-WRZ Series Sensor,

to Function as a Site Survey Tool for the FX-WRZ7860-0 One-to-One

Room Sensing System, or for the FX-ZFR Wireless Field Bus System

T-4000-119

Allen-Head Adjustment Tool: 1.6 mm (1/16 in.), 30 Tools for Each Bag

Technical specifications

Table 4: FX-WRZ Series Wireless Room Sensors

Product Codes

FX-WRZTHJ00-0: 

Temperature/Humidity Sensor with Display, Up/

Down Setpoint Adjustment Buttons, °C/°F Button, Relative Humidity

(RH) Button, and Occupancy Button

FX-WRZTTJ00-0: 

Temperature Sensor with Display, Up/Down Setpoint

Adjustment Buttons, °C/°F Button, and Occupancy Button

FX-WRZTTK00-0: 

Temperature Senor with Display, Up/Down Setpoint

Adjustment Buttons, °C/°F Button, Fan Speed Control Button, and

Occupancy Button

Power Requirements

3 VDC Supplied by Two 1.5 VDC AA Alkaline Batteries (Included with

Sensor); Typical Battery Life: 48 Months (36 Months Minimum)

Addressing

DIP Switches, Field Adjustable.

MS/TP Address, Network Number, and Zone Address

Ambient Conditions

Operating: 

0°C to 50°C (32°F to 122°F), 5% to 95% RH,

Noncondensing

Storage:

 

-

40°C to 71°C (

-

40°F to 160°F), 5% to 95% RH, Noncondensing

Wireless Band

Direct-Sequence Spread-Spectrum, 2.4 GHz ISM Band

Transmission Power

10 mW Maximum

Transmission Range

30 m (100 ft) Maximum Line of Sight;

15 m (50 ft) Recommended

Transmissions

Every 60 Seconds (±20 Seconds)

Temperature System

Accuracy

0.6°C/1.0°F Over the Range of 13°C to 29°C (55°F to 85°F);
0.9°C /1.5°F Over a Range of 0°C to 13°C (32°F to 55°F) and 29°C to

43°C (85°F to 110°F)

Temperature Sensor Type

Internal 10k ohm Negative Temperature Coefficient (NTC) Thermistor

Humidity Calibrated

Range

10% to 90% RH at 23°C (73°F)

Humidity Accuracy

3% across the range of 20% to 80%; 4% across the ranges 10% to 20%

and 80% to 90%

Materials

NEMA 1 White Plastic Housing

Mounting

Screw Mount or Double-Sided Adhesive Foam Tape Mount;
Double-Sided Adhesive Foam Tape Included

Dimensions

120 mm x 80 mm x 38 mm (4-3/4 in. x 3-1/32 in. x 1-1/2 in.)

Shipping Weight

0.14 kg (0.3 lb)

Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions

12

Summary of Contents for FX-WRZ Series















Reviews: