background image

D-308439 MP-802 PG+ Rev.0

 

 

Warranty

 

Visonic Ltd. 

(“

Seller

”)

 warrants the Products to the original purchaser only (the 

Buyer

”)

 against 

defective workmanship and materials under normal use of the Products for a period of twelve (12) 
months from the date of shipment by the Seller.

 

This Warranty is absolutely conditional upon the Products having been properly installed, 
maintained and operated under conditions of normal use in accordance with the Seller's 
recommended installation and operation instructions. Products which have become defective 
for any other reason, according to the Seller's discretion, such as improper installation, failure to

 

follow recommended installation and operational instructions, neglect, willful damage, misuse or 
vandalism, accidental damage, alteration or tampering, or repair by anyone other than the Seller, 
are not covered by this Warranty.

 

There is absolutely no warranty on software, and all software products are sold as a user license 
under the terms of the software license agreement included with such Product.

 

The Seller does not represent that Products may not be compromised and/or circumvented or that 
the Products will prevent any death and/or personal injury and/or damage to property resulting 
from burglary, robbery, fire or otherwise, or that the Products will in all cases provide adequate 
warning or protection. The Products, properly installed and maintained, only reduce the risk of such 
events without warning and it is not a guarantee or insurance that such events will not occur.

 

Conditions to Void Warranty

: This warranty applies only to defects in parts and workmanship 

relating to normal use of the Products. It does not cover:

 

 

damage incurred in shipping or handling;

 

 

damage caused by disaster such as fire, flood, wind, earthquake or lightning;

 

 

damage due to causes beyond the control of the Seller such as excessive voltage, mechanical 
shock or water damage;

 

 

damage caused by unauthorized attachment, alterations, modifications or foreign objects 
being used with or in conjunction with the Products;

 

 

damage caused by peripherals (unless such peripherals were supplied by the Seller;

 

 

defects caused by failure to provide a suitable installation environment for the products;

 

 

damage caused by use of the Products for purposes other than those for which they were 
designed;

 

 

damage from improper maintenance;

 

 

damage arising out of any other abuse, mishandling or improper application of the Products.

 

Items Not Covered by Warranty

: In addition to the items which void the Warranty, the following 

items shall not be covered by Warranty: (i) freight cost to the repair centre; (ii) customs fees, taxes, 
or VAT that may be due; (iii) Products which are not identified with the Seller's product label and lot 
number or serial number; (iv) Products disassembled or repaired in such a manner as to adversely 
affect performance or prevent adequate inspection or testing to verify any warranty claim. Access 
cards or tags returned for replacement under warranty will be credited or replaced at the Seller's 
option.

 

This warranty is exclusive and expressly in lieu of all other warranties, obligations 
or liabilities, whether written, oral, express or implied, including any warranty  of

 

merchantability or fitness for a particular purpose, or otherwise. In no case shall the SELLER 
be liable to anyone for any consequential or incidental damages for breach of this warranty 
or any other warranties whatsoever, as aforesaid.

 

The Seller shall in no event be liable for any special, indirect, incidental, consequential or 
punitive damages or for loss, damage, or expense, including loss of use, profits, revenue, or 

goodwill, directly or indirectly arising from Purchaser’s use or in

ability to use the Product, 

or for loss or destruction of other property or from any other cause, even if Seller has been 
advised of the possibility of such damage.

 

 

 

20 

MP-802 PG+ Wireless PIR Motion Detector Installation Guide

 

Summary of Contents for MP-802 P9M0























Reviews: