background image

 

8    

VA-8122 Proportional Valve Actuator Product/Technical Bulletin

 

S

pecifications 

Product 

VA-8122 Proportional Valve Actuator 

Power Requirements 

24 VAC at 50/60 Hz, 5.0 VA supply minimum, Class 2 

Input Signal 

Jumper Selectable:  0 (2) to 10 VDC, 0 (4) to 20 VDC, 6 (12) to 9 (18) VDC, 0 (4) to 20 mA 
Factory Setting: 

0 to 10 VDC, Drive Down (DD) action on signal increase 

Input Impedance 

Voltage Input: 

0 to 10 VDC, 150,000 ohms and 0 to 20 VDC, 450,000 ohms 

Current Input: 

0 to 20 mA, 500 ohms 

5/16 in. Stroke Time 

50 Hz: Approximately 108 seconds nominal 
60 Hz: Approximately 90 seconds nominal 

Force 

Shutoff and Breakaway: 

22 lb (98 N) minimum 

Cycles 

60,000 full cycles; 1,500,000 repositions 

Enclosure 

NEMA 1, IP20 

Audible Noise Rating 

35 dBA maximum at 3.28 ft (1 m) 

Ambient Operating 

Conditions 

35 to 135°F (2 to 57°C);  
85°F (30°C) maximum dew point at 90% RH, non-condensing 

Ambient Storage 

Conditions 

-40 to 150°F (-40 to 65°C);  
85°F (30°C) maximum dew point at 90% RH, non-condensing 

Valve Media Temperature 

Water:  195°F (90°C) maximum 
Steam:  Actuator is not rated for this application. 

Dimensions (H x W x D) 

4.5 x 5.0 x 2.5 in. (114 x 127 x 64 mm) 

Shipping Weight 

1.6 lb (0.74 kg) 

Agency Compliance 

UL 873 Recognized, File E27734, Guide XAPX2 
CSA C22.2 No. 139 Certified, File LR85083, Class 3221 02 

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication 
or misuse of its products. 

 

European Single Point of Contact: 

NA/SA Single Point of Contact: 

APAC Single Point of Contact: 

JOHNSON CONTROLS 
WESTENDHOF 3 
45143 ESSEN 
GERMANY 

JOHNSON CONTROLS 
507 E MICHIGAN ST 
MILWAUKEE WI 53202 
USA 

JOHNSON CONTROLS 
C/O CONTROLS PRODUCT MANAGEMENT 
NO. 22 BLOCK D NEW DISTRICT 
WUXI JIANGSU PROVINCE 214142 
CHINA 

 

Building Efficiency

 

507 E. Michigan Street, Milwaukee, WI  53202 

 

 

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.  

All other marks herein are the marks of their respective owners. © 2016 Johnson Controls, Inc.

 

Summary of Contents for VA-8122









Reviews: