background image

C

ONTACT

H

UMMINBIRD

Web site

humminbird.com

E-mail

service@humminbird.com

Telephone

1-800-633-1468

Direct Shipping

Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA

WARNING!

This device should not be used as a navigational aid

to prevent collision, grounding, boat damage, or personal injury.
When the boat is moving, water depth may change too quickly
to allow time for you to react. Always operate the boat at very
slow speeds if you suspect shallow water or submerged objects.

WARNING!

Disassembly and repair of this electronic unit should

only be performed by authorized service personnel. Any
modification of the serial number or attempt to repair the
original equipment or accessories by unauthorized individuals
will void the warranty.

WARNING!

This product contains chemicals known to the State

of California to cause cancer and birth defects or other
reproductive harm.

WARNING!

Do NOT travel at high speed with the unit cover

installed. Remove the unit cover before traveling at speeds above
20 mph.

ENVIRONMENTAL COMPLIANCE STATEMENT:

It is the intention of

Johnson Outdoors Marine Electronics, Inc. to be a responsible
corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities
where we make or sell our products.

WEEE DIRECTIVE:

EU Directive 2002/96/EC “Waste of Electrical and

Electronic Equipment Directive (WEEE)” impacts most distributors,
sellers, and manufacturers of consumer electronics in the European
Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from
their products to achieve environmentally responsible disposal during
the product life cycle.

WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed
and intended as fixed or temporary installation in transportation
vehicles such as automobiles, aircraft, and boats. In some European
Union member states, these vehicles are considered outside of the
scope of the Directive, and EEE for those applications can be
considered excluded from the WEEE Directive requirement.

This symbol (WEEE wheelie bin) on product indicates the

product must not be disposed of with other household refuse. It
must be disposed of and collected for recycling and recovery of
waste EEE. Johnson Outdoors Marine Electronics, Inc. will mark

all EEE products in accordance with the WEEE Directive. It is our goal to
comply in the collection, treatment, recovery, and environmentally
sound disposal of those products; however, these requirements do vary
within European Union member states. For more information about
where you should dispose of your waste equipment for recycling and
recovery and/or your European Union member state requirements,
please contact your dealer or distributor from which your product was
purchased.

ROHS STATEMENT:

Product designed and intended as a fixed

installation or part of a system in a vessel may be considered beyond
the scope of Directive 2002/95/EC of the European Parliament and of
the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.

© 2015 Johnson Outdoors Marine Electronics, Inc. All rights reserved.

O

VERVIEW

Following are instructions for the installation of this accessory. Before you start the installation, we
encourage you to read these instructions carefully in order to get the full benefit from your
Humminbird® accessory.

Installation Kit:

This accessory includes the following supplies*:

(2) bolts, hex head 1/4-20 x 4"

(2) 1/4" split-ring washers

(2) hex nuts, 1/4 - 20

(2) screws, 1/4-20 x 3/8"

(2) end caps

(1) mounting template

*Product supplies and features are subject to change without notice.

Customer Service:

If you find that any items are missing from your installation kit, visit our Web site

at

humminbird.com

or call Customer Service at

1-800-633-1468

.

Supplies:

In addition to the hardware supplied with your installation kit, you will need a drill and various

drill bits, a cutting tool for the dashboard material, a Phillips head screwdriver, a wrench, safety glasses
and a dust mask, and masking tape.

I

NSTALLATION

Perform the procedures in the following sections to in-dash mount the ONIX® control head.

NOTE:

Your control head might not look exactly like the illustrations in this guide, but the

control head will mount in the same way.

1

|

Determine the Mounting Location

Start by locating a suitable, flat area of the dashboard for mounting. Consider the following to find the
best mounting location:

Standard Compass Safe Distance:

The control head must be installed at least 4 ft (1.2 m)

from the compass or other magnetic equipment on the vessel. Also, see your compass
installation guide for details.

Interference:

The mounting location must provide adequate distance from electric motors or

any equipment that may cause electronic interference.

Stability:

The mounting area should be protected from waves, shock, vibration, and water.

Visibility:

The operator must have a clear view of the screen during operation. Review the visibility

in relation to other dashboard equipment, sun, and the operator’s main steering position.

Cover:

See the In-dash Mounting Template to allow space for the cover.

Depth:

The mounting area should have a depth of 6" (152.4 mm) to allow space for the control

head and cables.

Ventilation:

The area beneath the mounting surface should be well-ventilated.

Accessibility:

The location should be easily accessible for all cables to reach the ports on the

back of the control head.

NOTE:

If a cable is too short for your application, extension cables are available. For

assistance, contact Customer Service.

IN-DASH MOUNTING

Installation Guide

1

532105-2_A

IN-DASH MOUNTING

Installation Guide

4

532105-2_A

Planning Depth Space for the

Control Head and Cables

6" (152.4 mm)

ONIX_IDMK_IG_532105-2_A.qxp:ONIX Installation Guide  6/1/15  12:00 PM  Page 4

Summary of Contents for Humminbird ONIX

Page 1: ...cation Start by locating a suitable flat area of the dashboard for mounting Consider the following to find the best mounting location Standard Compass Safe Distance The control head must be installed at least 4 ft 1 2 m from the compass or other magnetic equipment on the vessel Also see your compass installation guide for details Interference The mounting location must provide adequate distance fr...

Page 2: ...her three corners as indicated on the template Use one of the corner holes as an entry hole or drill an additional entry hole away from the main cut line 5 Carefully begin cutting toward the dotted cut line and continue cutting to the inside of the line around the template CAUTION The corner cut lines are critical to the installation Carefully cut along the inside of the line 6 Test the Mounting H...

Page 3: ...e submerged in water or flooded If cables are installed in a splash prone area it may be helpful to apply dielectric grease to the inside of the connectors to prevent corrosion Dielectric grease can be purchased separately from a general hardware or automotive store 2 Route the cables to the control head and insert the connectors into the proper ports on the control head The ports are labeled and ...

Page 4: ...onics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle WEEE compliance may not be required in your location for electrical electronic equipment EEE nor may it be required for EEE designed and intended as fixed or temporary installation in transportation vehicles such as automobiles aircraft and boat...

Reviews: