background image

15

J O H N S O N   F I T N E S S   T R E A D M I L L   T 8 0 0 0 / T 8 0 0 0   P R O

14

J O H N S O N   A I R   R O W E R   W 8 0 0 0

J O H N S O N   A I R   R O W E R   W 8 0 0 0

   
   

MAINTENANCE

Johnson Air Rower W8000 is for use in the commercial environment. However, as a club 

manager or owner, you are responsible for cleaning and maintaining the unit’s integrity. If you 

fail to maintain the bike as described below, it could affect or void the Johnson limited warranty.

NOTE:

 Safety of the equipment can be maintained only if the equipment is examined regularly 

for damage or wear. Keep the equipment out of use until defective parts are repaired or 

replaced. Pay special attention to parts that are subject to wear, such as the rope.

DAILY INSPECTION

Look and listen for loose fasteners, unusual noises, and any other indications that the 

equipment may be in need of service. If you notice any of these, obtain service.

DAILY MAINTENANCE

Johnson Fitness recommends the Air Rower be cleaned before and after each workout. The 

following daily maintenance tips will keep your unit operating at peak performance:

1) Use a damp, soft cloth with water or mild liquid detergent to clean all exposed surfaces.

    DO NOT use ammonia, chlorine, or acid-based cleaners.

2) Keep the display console free of fingerprints and salt build-up caused by sweat.

3) Frequently vacuum the floor underneath the unit to prevent the accumulation of dust and

    dirt, which can affect the smooth operation of the unit.

4) Check for dust inside flywheel with flashlight. 

*Product specifications are subject to change without notice.

PRODUCT SPECIFICATIONS

Extra-large LCD display

Time, Distance, SPM (strokes per minute), Stroke, Watts, Heart Rate, Calories

Manual, Race, Training

Yes

Fan blade system

12

Coil spring poly-V belt

41 kg / 90 lbs

160 kg / 350 lbs

Battery powered for LCD display

Easy-to-grip wooden handrail

Fit-in-with adjustable footboard

Aluminum

W8000

CONSOLE

Display Screen

Display Readout

Programs

Telemetric Receiver

TECHNICAL DATA

Resistance Technology

Resistance Levels

Drive System

Product Weight

Max User Weight

Power Requirement

SPECIAL FEATURES

Handlebar Design

Pedals

Monorail

Summary of Contents for AIR ROWER W8000










Reviews: