10
- Assemble the most appropriate accessory
according to what is indicated in the sec-
tions:
DISC (D) grate and slice,
BLADE (E) mince,
ACCESSORY (F) mix, beat, amalgamate.
On selecting and assembling the most sui-
table accessory, place the lid on the cup.
- Position the lid by centring it on the pin
and rotating in a counter clockwise direc-
tion. Block the three grooves on the lid onto
the three teeth on the cup. Make sure the
safety arm (C3) is inserted into the slot of
the motor base (A4).
Using the blending jug
(
B
)
- After removing the shaft (A5) from the
motor base, reposition the cup (C) on the
motor base (A). Make sure the three small
blocks around the rotating centre are in-
serted into their lodgings under the cup.
Check that there are NO accessories in the
cup.
- Position the lid and turn in a counter
clockwise direction to block the three
grooves onto the three teeth of the cup.
Make sure the safety arm (C3) is inserted
into the slot of the motor base (A4).
- Remove the safety lid (A1) from the ap-
pliance by turning in a counter clockwise
direction.
- Position the jug (B) with the handle facing
away from the cup (C) and turn in a counter
clockwise direction until it clicks into place.
- Insert the food to process and then add
the liquid. It is very important that the li-
quid does not exceed the maximum level
indicated on the cup.
- Place the lid (B2) on the jug and turn in a
clockwise direction until the two front
spouts coincide and it clicks into place.
- Position the measuring cap (B1) and re-
move it only for the time necessary to add
the ingredients.
- Start the processing by setting the most
suitable program on the selector (A6): 1 for
low speed and 2 for high speed.
- Turn the selector (A6) in a counter clock-
wise direction to activate the Pulse fun-
ction.
- The appliance reaches a high speed with
this function, which immediately stops
once the selector is released.
- The Pulse function (turn-release…turn-
release) is suitable for preparing shakes.
- Depending on the type of food, the jug
can blend up to 1.2 litres.
- Never use the jug and cup to process
substances at the same time. After comple-
ting the processing, position the switch
(A6) on 0. Wait for the appliance to stop
completely before removing the jug.
- To remove the lid from the jug, press the
safety button (B3) and at the same time
turn the lid in a counter clockwise direction.
DISC
(
D
)
grate and slice
Assemble the cup according to the instruc-
tions in the chapter “Using the Cup (C)”.
Insert the pin (G) into the centre of the re-
versible disc (D).
To grate, the grating blade (D1) of the disc
(D) must be facing upwards.
To slice, the slicing blade (D2) of the disc
(D) must be facing upwards.
Let the three teeth of the pin enter the
three grooves of the disc and then turn the
disc and pin in opposite directions until
they are securely locked into place.
Position the disc+pin assembled on the
shaft of the cup (A5). Close the lid accor-
ding to the instructions described above.
Introduce the food into the cup by delica-
tely pressing it towards the blade with the
food-pressing accessory (C1).
Never use your fingers or other objects.
Start rotating the disc (D) by turning the se-
lector (A6)
On completion of the processing, place the
selector (A6) on the “0” position.
Turn the lid in a clockwise direction to re-
move the safety arm (C3) from the slot of
the motor base (A4).
Rest the cup on a stable surface before
completely removing the lid and retrieve
the accessory used.
Be careful when handling the blades of the
accessory used.
Pour the processed food and thoroughly
wash the accessories and cup.
BLADE
(
E
)
mince
Assemble the cup according to the instruc-
tions in chapter “Using the Cup (C)”.
Carefully remove the plastic protection
from the blades (E).
Insert the blades (E) into the pin (G) by pu-
shing downwards, so that the base of the
MustangISTRUZIONI11-11.Qxd_Layout 1 30/05/13 10:33 Pagina 10
