27
28
STROLLER OPERA
TION
STROLLER OPERA
TION
For larger child, use shoulder harness anchor A and the highest shoulder slots.
For smaller child, use shoulder harness anchor B and the lowest shoulder slots.
Use either shoulder harness anchor in the slots that are closest to child's
shoulder height.
(Fig. 16)
Use slide adjuster to change the harness length.
(Fig. 17.1)
Press the button
(Fig. 17.2)
, while pulling the waist harness to proper length
(Fig. 17.3)
Use Shoulder Harness Cover
The shoulder harness cover can be removed from the webbing. To assemble
shoulder harness cover in reverse steps.
Adjust Calf Support
The calf support has 3 positions.
Raise Calf Support
To raise the calf support, just push it upwards.
Lower Calf Support
Press the adjustment buttons on both sides of the calf support
(Fig. 18.1)
,
and rotate the calf support downwards.
(Fig. 18.2)
Use Front Swivel Lock
Pull up the front swivel locks to maintain the moving direction.
(Fig. 19)
Tip
It is recommended to use swivel locks on uneven surfaces.
Use Brake
To lock wheels, step the brake lever downwards.
(Fig. 20)
To release wheels, just lift the brake lever upwards.
Tip
Always apply brake when stroller is in stopped position.
Use Hood
To open the hood, pull hood forwards and press stretchers down on both
sides.
(Fig. 21)
To fold the hood, pull up the stretchers on both sides
(Fig. 21.1)
and pull hood
toward back.
Fold Strolle
r
Press the folding button
(Fig. 22.1)
and rotate the folding handle upwards
(Fig. 22.2)
, push the stroller forward to fold
(Fig. 22.3)
. Lock the stroller by
tucking storage latch onto the storage mount
(Fig. 23.1)
, then the stroller is
folded and locked completely.
(Fig. 23)
Use Carry Strap
You can carry the stroller with ease by lifting the carry strap.
(Fig. 24)
Use Rain Cover
To assemble the rain cover
(Fig. 25)
, place it over the stroller, and then attach
the hook and loop fasteners on the rain cover.
(Fig. 26)
!
Before using the rain cover, please make sure the backrest has been adjusted
to the lowest position and the infant car seat has been fastened.
!
When using the rain cover, please always check its ventilation.
!
When not in use, please check the rain cover has been cleaned and dried
before folding.
!
Do not fold the stroller after assembling the rain cover.
!
Do not place your child into the stroller assembled with rain cover during hot
weather.
Use Footmuff
The soft footmuff can provide your child with a warm and comfortable
environment.
(Fig. 27)
Assemble the footmuff by following these steps.
1. Before assembling the footmuff, Please release the buckle and remove
the shoulder cover.
2. Place the footmuff over the seat after unziping it, thread the shoulder
harnesses, waist harnesses and crotch harness through respective slots.
(Fig. 28)
3. Assemble the shoulder cover to the unit.
4. Stick the hook and loop fasteners.
(Fig. 29)
5. Place baby into the footmuff, lock the safety buckle, and then rezip the
footmuff. The assembled footmuff is shown as.
(Fig. 30)
!
For the using method for restraint system, please refer to the relevant
section in the instruction manual.
Summary of Contents for brisk
