background image

Figure 1

Series connection

Parallel connection

Figure 2

Parallel connection after series connection 

5.8  Fuse

         The fuse should be connected to each 
non-grounded pole of the array (in other 
words, if system is not grounded, the fuse 
should be connected to both positive and 
negative terminals).

         b) The fuse rating also corresponds 
to the maximum reverse current that the 
module could withstand (when an array is 
shading, the array is loaded into another 
parallel module array to generate power), 
thus the number of parallel connected 
arrays is affected.

         c) It is forbidden to connect two or 
more strings in parallel and then share 
the fuses.

         a) The maximum rating of the fuse 
connected in series is 30A, and the module
- s p e c i fi c   ra t i n g s   a r e   a va i l a b l e   o n   t h e  
product label and product data sheet.

5.7  Wiring

         In order to ensure PV system could 
operation smoothly, when connecting modules 
or connecting loads (such as inverters batteries, 
etc.), ensure that the polarity of the cables is 
properly connected (Figure 1 and Figure 2). 
If modules are not connected properly, the 
bypass diode may be damaged. Modules 
could be connected in series to increase 
voltage. Connecting modules in series by 
inserting the positive terminal of one module 
into the negative terminal of the next module. 
Figure 1 shows the serial connection of 
modules. Modules could be connected in 
parallel to increase current (shown in Figure 2). 
Connecting modules in series in Parallel by 
inserting the positive terminal of one module 
into the negative terminal of the next module. 
The number of modules connected in series 
or in parallel needs to be reasonably designed 
according to the system configuration. All 
instructions above must be followed to meet 
the Jolywood Warranty valid conditions.

13

Jolywood (Taizhou) Solar Technology Co.,Ltd.

Kaiyang Rd., Jiangyan Economic Development zone, Taizhou City, Jiangsu Province, P. R. China

www.jolywood.cn

 mkt@jolywood.cn

 +86-523-8061 2361

Installation Manual

 - Jolywood N-type Mono-crystalline Double Glass Module

Summary of Contents for JW-HD108N

















Reviews: